Troy-Bilt 52065 owner manual Compact Storage, TRIMMER/MOWER Cleaning and Debris Removal

Page 15

 

Section 5: Maintenance

15

 

 

 

 

 

 

WARNING

Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models.

Failure to follow these instructions can result in serious personal injury or property damage.

TRIMMER/MOWER CLEANING AND DEBRIS REMOVAL

Regular cleaning of debris from around the engine and on the machine is required for maximum engine efficiency and good over- all performance. Inspect and clean the fol- lowing areas regularly, making sure the engine is stopped – and cool – before pro- ceeding:

Brush and wipe off all engine surfaces, especially before checking oil or adding fuel. Do not let oil or grease accumu- late. For access to the front of the engine, the debris shield can be lifted up and tilted forward.

Wipe the deck clean, particularly near the engine muffler.

Clean the underside of the deck.

Keep safety and operating decals clean and legible.

Keep all control levers clean so they work properly.

COMPACT STORAGE

For compact storage, remove the two screws and locknuts securing the handle- bar and carefully (to avoid kinking the cables) rotate the handlebar so that the upper portion rests on the engine and the handlebar legs face to the rear of the unit.

GENERAL ENGINE MAINTENANCE

Perform the following engine maintenance for your engine according to the engine maintenance schedule and instructions in the separate Engine Owner’s Manual:

Engine Oil Service – Check the engine oil level before starting the engine and after each 5 hours of continuous operation. Running the engine when it is low on oil will quickly ruin the engine.

Change the oil after every 25 hours of operation and more often when operating in extremely dirty or dusty conditions.

Air Cleaner Service – The air cleaner fil-

ters dirt and dust out of the air before it

enters the carburetor. Operating the

engine with a dirty, clogged air filter can

cause poor performance and damage to the engine. Never operate the engine with- out the air cleaner installed. Inspect and service the air cleaner after every 25 oper- ating hours, more often if operating in very dusty or dirty conditions. Refer to the Engine Owner’s Manual for cleaning or replacement instructions.

Spark Plug – Inspect and clean or replace the spark plug after every 100 operating hours or annually. Refer to the Engine Owner’s Manual for cleaning or replace- ment instructions.

Spark Arrester Screen – If the engine is equipped with a spark arrester screen, remove and clean it according to the time intervals and instructions in the Engine Owner’s Manual.

Engine Cleaning – The engine must be kept clean to assure smooth operation and to prevent damage from overheating. Refer to the Engine Owner’s Manual for specific cleaning instructions.

Carburetor/Governor Control Adjustments – The carburetor was adjusted at the factory for best operating speed. Refer to the Engine Owner’s Manual for any adjustment information.

The governor controls the maximum safe operating speed and protects the engine and other moving parts from damage caused by overspeeding. Do not tamper with the governor settings. Seek autho- rized service if you think an adjustment is required.

Throttle Control Adjustment – If the engine does not shut off when the throttle lever is moved to the stop position, or if the engine does not respond to various throttle settings, refer to the Engine Owner’s Manual for service information.

OFF-SEASON STORAGE

When storing the machine for extended periods, follow these procedures to ensure that the unit will be in good condi- tion for future use.

Store machine on a level surface.

Thoroughly inspect the machine for any loose, broken or missing parts. Repair or replace parts as necessary.

Protect the engine and perform the rec- ommended engine maintenance by fol- lowing the engine storage instructions found in the Engine Owner’s Manual. Be sure to protect the fuel lines, carburetor and fuel tank from gum deposits by removing fuel or by treating fuel with a fuel stabilizer (follow the engine manu- facturer’s recommendations).

WARNING

Never perform maintenance when engine is running or spark plug wire is connected, except when instructed to do so.

Never store mower with fuel in fuel tank inside a building where fumes can reach an open flame or spark, or where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc. Make sure engine is cool before storing.

Drain gasoline outdoors into an approved container.Do not smoke and keep fuel away from open flame.

Failure to follow these instructions will result in serious personal injury or prop- erty damage.

Clean any dirt, grass or chaff from the air cooling system intake area and other parts of the engine.

Disconnect spark plug wire from spark plug. Prevent wire from touching spark plug by placing wire away from spark plug.

Image 15
Contents Trimmer/Mower Table of Contents General Operation SafetyDo not ServiceSlope Operation ChildrenSafety Decals HandlebarOn right Handlebar On right side, rear Mower deck Assembly Assembly StepsIntroduction Assembly Features and Controls Features and ControlsRecoil starter G, -1 is used to pull start the engine Operation PRE-START ChecklistAdjust Handlebar Height Adjust Line Cutting HeightOperating the Machine Using the Trimmer Head Control BailMaterials to the right side Operating Tips & TechniquesTo Adjust Belt Tension MaintenanceMaintenance Schedule Adjusting Trimmer Head EngagementBelt Replacement Inspecting and Replacing the Drive BeltBelt Inspection Belt Performance Troubleshooting Cleaning the EngineLubrication TRIMMER/MOWER Cleaning and Debris Removal General Engine MaintenanceCompact Storage Trimmer lines can be changed To Change Trimmer LinesProblem Possible Cause Correction TroubleshootingDrawing no Ref. # Description Qty Ref. # DescriptionParts List Parts List Drawing no 715 133 Accessories and Kits Owner Registration Card Warranty ServiceReplacement Parts Engine Service and Repair

52065 specifications

The Troy-Bilt 52065 is a robust and versatile tiller designed for gardening enthusiasts and professional landscapers alike. Known for its durable construction and innovative features, this machine is engineered to make soil preparation more effortless and efficient.

At the heart of the Troy-Bilt 52065 is its powerful engine, which typically boasts around 160 cc, ensuring ample power for breaking up compacted soil and tackling tough gardening tasks. The tiller is equipped with a 12-inch steel tines that are capable of tilling a width of 16 inches, making it suitable for both large and small gardens. The tines are designed for optimal performance, allowing for efficient weed control and soil aeration.

One of the standout features of the Troy-Bilt 52065 is its adjustable handle. This allows users of different heights to operate the tiller comfortably. Additionally, the handle can be folded down for easy storage, making it a practical choice for those with limited garage space.

This tiller also incorporates Troy-Bilt's patented "Forward and Reverse" tilling capability. This feature provides users with added maneuverability, enabling them to till tough soil in both directions. It significantly reduces the time spent on the job, allowing for a smoother tilling experience.

Another noteworthy characteristic of the Troy-Bilt 52065 is its easy-to-use controls. The intuitive throttle control and gear shift are conveniently located, allowing the operator to adjust speed and power without difficulty. This usability is a key selling point for both novice and experienced gardeners.

The machine's construction is solid, featuring a heavy-duty steel frame that can withstand the rigors of frequent use. Its wheels are designed for enhanced traction, making it easier to navigate various terrain types. With maintenance in mind, the Troy-Bilt 52065 is designed for straightforward access to components, ensuring that routine maintenance is an uncomplicated task.

In conclusion, the Troy-Bilt 52065 is an exceptional tiller that excels in performance, durability, and ease of use. Its blend of powerful features, innovative technology, and ergonomic design makes this tiller a valuable addition to any gardening toolkit. Whether preparing a new bed for planting or maintaining an existing garden, the Troy-Bilt 52065 delivers reliability and efficiency, making gardening tasks enjoyable rather than laborious.