Troy-Bilt 13101-GTX 16 manual Visually Check, Check Battery, Check Tire Pressure, Adjust Seat

Page 15

Before Operation (continued)

Lift seat adjustment lever (Z) and slide seat forward or backward.

Z

 

Models

 

13074 & 13076

Fig. 5-2

 

 

Loosen adjustment knobs (ZZ), slide seat forward or backward.

ZZ

Auxilliary

Attachment Lift

 

Hydraulic Lever

 

Lever (K)

Attachment/PTO Drive

(Model 13076 Only)

 

Switch (X)

(L)

 

 

 

Light

 

Throttle (J)

Switch (E)

 

 

Cruise Control Switch

 

Travel

(Models 13074 & 13076)

 

Pedal (M)

(O)

 

 

Choke Lever (G)

 

 

 

 

Ignition/Starter

Brake/Neutral

 

Switch (H)

 

 

Pedal (F)

 

 

 

 

Parking Brake Lever (N)

Fig. 5-4

 

 

Fig. 5-3

Model 13101

 

 

4. Visually Check

Check for and repair loose or missing screws, nuts, and damaged parts.

5. Check Battery

To connect the battery initially, remove the red (+) terminal cover from the (+) positive terminal and connect the red battery cable to this terminal. Tighten the hardware before sliding the boot over the terminal.

Next, remove the black (-) terminal cover from the batery and connect the black (-) battery cable. Tighten the hardware. If cables are corroded, clean them. See “Battery”, page 22.

DANGER

BATTERIES PRODUCE EXPLOSIVE GASSES. KEEP OPEN FLAMES AND SPARKS AWAY. DO NOT SET TOOLS ACROSS TERMINALS.

BATTERY ELECTROLYTE CAN CAUSE SEVERE BURNS. EYE CONTACT CAN CAUSE BLINDNESS. ALWAYS WEAR EYE PROTECTION AND RUBBER GLOVES WHEN WORKING NEAR BATTERY. NEVER WEAR JEWELRY.

IF ELECTROLYTE CONTACTS SKIN OR EYES, RINSE IMMEDIATELY WITH WATER FOR AT LEAST 15 MINUTES. CALL PHYSICIAN IMMEDIATELY.

6. Check Tire Pressure

Front –

12 to 14 PSI (82 to 96 kPa)

Rear –

8 to 10 PSI (55 to 68 kPa)

7. Adjust Seat

Models 13074 & 13076 - To adjust seat, lift lever (Z, Fig. 5-2) and slide seat forward or backward. Release lever.

Model 13101 - To adjust seat,loosen adjustment knobs (ZZ, Fig. 5-3) and slide seat forward or backward.

Tighten adjustment knobs.

8.Perform Electric Clutch Break-in Procedure

Perform this step before initial use and after extended storage.Before operating unit, start engine as instructed on page 16. With the engine running at full speed, engage and disengage attachment/PTO drive switch (X, Fig. 5-4) 10 to 15 times.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models GTX 18 18 HP GTX 20 20 HP GTX 16 16 HP Safety Operation MaintenanceIntroduction Table of ContentsIdentification Numbers Service InformationPreparation SectionSafe Operating Practices for This Unit IntroductionTrainingOperation SafetyBefore Operation Handling GasolineChildren Slope OperationBe alert and turn machine off if children enter the area Stopping MaintenanceEngine BatteryStorage Safety DecalsSpecifications Attachments, Kits & SpecificationsNumber Description Attachment, Kits and SpecificationsIgnition/Starter Switch N Throttle LParking Brake Lever a Controls Do not mix oil with gasoline Check Engine Oil LevelFill Fuel Tank Check Engine Flywheel ScreenCheck Tire Pressure Check BatteryAdjust Seat Visually CheckThrottle Setting Starting Engine Turn attachment/PTO drive switch X, -1 to OFFStopping Engine Hydraulic Attachment Lift Perform Electric Clutch Break-in ProcedureInterlock System Attachment/PTO DriveTo activate lights, press light switch E, -3 to on Hydrostatic TransmissionSpeed Models Model 13076 Only Moving Tractor Manually Cruise ControlBrake / Neutral Pedal Parking Brake Lever Changing Engine Oil Filter Models 13074To Check Engine Oil Level Changing Engine OilFuel Filter Engine Air CleanerService Paper Element Engine Air Intake ScreenSpark Plugs Front Axle AdjustmentPower Steering CarburetorHydrostatic Maintenance and Lubrication Proper Jack PlacementInterlock Switches Brake AdjustmentTighten jam nuts F Hydrostatic Neutral AdjustmentAmt. Required Lubrication ChartTroubleshooting Chart Storing the Tractor Interval ServiceGarden Way Incorporated

13074-GTX 18, 13101 - GTX 16, 13101-GTX 16 specifications

Troy-Bilt has long been a trusted name in outdoor power equipment, and models like the Troy-Bilt 13101-GTX 16, 13101-GTX 16, and 13074-GTX 18 are a testament to the brand’s commitment to quality and innovation. These tillers are designed to make gardening and landscaping tasks efficient and enjoyable, featuring an array of advanced technologies and characteristics that cater to both novice and seasoned gardeners.

The Troy-Bilt 13101-GTX 16 is engineered for easy operation and maneuverability. Its lightweight design allows users to navigate around gardens effortlessly. Equipped with a robust 16-inch tilling width, it is perfect for small to medium gardening tasks, providing ample coverage without overwhelming the user. The adjustable tilling depth control system ensures that users can achieve the desired soil conditions for various planting needs.

In terms of power, the 13101-GTX 16 is powered by a reliable engine that delivers consistent performance, even in tougher soil conditions. This model also features a gear-driven transmission that allows for smooth operation and better power transfer, ensuring efficient tilling with minimal effort.

The Troy-Bilt 13074-GTX 18 elevates the features found in its 16-inch counterpart, offering a wider 18-inch tilling width. This model is particularly advantageous for larger gardens or plots, allowing users to cover more ground in less time. Moreover, it boasts a heavy-duty build with forged tines that can penetrate even the hardest soil, making it a resilient option for more extensive projects.

Both models incorporate Troy-Bilt’s patented just-a-twist adjustment feature, enabling users to easily switch between forward and reverse tilling directions. This functionality enhances control and versatility, making it easier to navigate around obstacles and till tight spaces.

Another notable feature across these models is the Ergo Handles, designed for comfort and reduced fatigue during extended usage. The cushioned grips provide a secure hold, minimizing vibrations and enhancing user experience.

In summary, the Troy-Bilt 13101-GTX 16, 13101-GTX 16, and 13074-GTX 18 combine user-friendly designs with powerful performance, making them excellent choices for anyone looking to cultivate their green thumb. Whether you are preparing a small flower bed or tilling a larger vegetable garden, these tillers promise reliability, power, and ease, solidifying Troy-Bilt’s reputation as a leading manufacturer in outdoor equipment.
Top Page Image Contents