Troy-Bilt Maintenance Tips for Troy Bilt GTX 16 and GTX 18 Lawn Mowers
Page 22

Maintenance (continued)

Carburetor

The carburetor is adjusted at the factory. It should not need resetting. If black exhaust is noted, check the air cleaner first. An over-rich fuel mixture is usually caused by a poorly serviced or clogged air cleaner element, not an improperly adjusted carburetor. If readjustment is necessary, refer to the engine manual or see your dealer.

Battery

The battery is maintenance-free and the acid level cannot be checked. Keep cables and terminals clean. If cables are corroded, clean them.

DANGER

Spark Plugs

Every 100 hours remove and inspect spark plugs. Do not service a plug which is in poor condition. Best results are obtained with a new plug. Under good operating conditions, the plug will have a light gray coating or a tan deposit. A white, blistered coating could indicate engine overheating. A black (carbon) coating could indicate an over-rich fuel mixture caused by a clogged air cleaner or improper carburetor adjustment. See engine manual for spark plug specifications.

NOTE: Do not clean spark plugs in machines which use abrasive grit. Clean spark plugs by scraping, wire brushing or washing with a commercial solvent.

Front Axle Adjustment

2.Adjust screws (N, Fig. 7-5). These screws apply pressure to the front axle. Axle should pivot with a small amount of drag.

Front Wheel Alignment

Straighten front wheels. Loosen locknuts (Q, Fig. 7-5). Adjust tie rod (Z) so measurement (O) is 1/8" longer than measurement (P).

Power Steering

Power steering is controlled by the hydraulic system. No adjustment is necessary.

BATTERIES PRODUCE EXPLOSIVE GASSES. KEEP OPEN FLAMES AND SPARKS AWAY. DO NOT SET TOOLS ACROSS TERMINALS.

BATTERY ELECTROLYTE CAN CAUSE SEVERE BURNS. EYE CONTACT CAN CAUSE BLINDNESS. ALWAYS WEAR EYE PROTECTION AND RUBBER GLOVES WHEN WORKING NEAR BATTERY. NEVER WEAR JEWELRY.

In time, a gap may form between the bolster and front axle. See Fig. 7-5. The following adjustment can reduce play in the axle. To make adjustment:

1.Set parking brake. Securely block rear wheels. Raise front of tractor with a hoist or jack. See page 23 for jacking instructions.

IF ELECTROLYTE CONTACTS SKIN OR EYES, RINSE IMMEDIATELY WITH WATER FOR AT LEAST 15 MINUTES. CALL PHYSICIAN IMMEDIATELY.

After cleaning battery, apply a light coat of petroleum jelly or grease to terminals and over the bolt stud.

Remove battery cables before removing battery. Remove negative (-) cable first, followed by the positive (+) cable. Always check the polarity of the battery terminals. Make sure the battery is not reversed. The negative (-) cable is the ground.

ALWAYS CONNECT THE NEGATIVE (-) TERMINAL LAST.

Adjust screws (N) at each side to tighten gap. Gap

FRONT

View from

under tractor.

P

Q

N

Z

Measure distance (P) and distance (O) at the outside edges of each tire.

Charging: If the unit has not been used for an extended time period, charge the battery at 6 to 10 amps for 1 hour.

O

Fig. 7-5

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Safety Operation Maintenance Models GTX 18 18 HP GTX 20 20 HP GTX 16 16 HPTable of Contents IntroductionService Information Identification NumbersIntroductionTraining SectionSafe Operating Practices for This Unit PreparationHandling Gasoline SafetyBefore Operation OperationSlope Operation ChildrenBe alert and turn machine off if children enter the area Maintenance StoppingBattery EngineSafety Decals StorageAttachments, Kits & Specifications SpecificationsAttachment, Kits and Specifications Number DescriptionThrottle L Ignition/Starter Switch NParking Brake Lever a Controls Check Engine Flywheel Screen Check Engine Oil LevelFill Fuel Tank Do not mix oil with gasolineVisually Check Check BatteryAdjust Seat Check Tire PressureTurn attachment/PTO drive switch X, -1 to OFF Throttle Setting Starting EngineStopping Engine Attachment/PTO Drive Perform Electric Clutch Break-in ProcedureInterlock System Hydraulic Attachment LiftHydrostatic Transmission To activate lights, press light switch E, -3 to onSpeed Models Model 13076 Only Cruise Control Moving Tractor ManuallyBrake / Neutral Pedal Parking Brake Lever Changing Engine Oil Models 13074To Check Engine Oil Level Changing Engine Oil FilterEngine Air Intake Screen Engine Air CleanerService Paper Element Fuel FilterCarburetor Front Axle AdjustmentPower Steering Spark PlugsBrake Adjustment Proper Jack PlacementInterlock Switches Hydrostatic Maintenance and LubricationHydrostatic Neutral Adjustment Tighten jam nuts FLubrication Chart Amt. RequiredTroubleshooting Chart Interval Service Storing the TractorGarden Way Incorporated

13074-GTX 18, 13101 - GTX 16, 13101-GTX 16 specifications

Troy-Bilt has long been a trusted name in outdoor power equipment, and models like the Troy-Bilt 13101-GTX 16, 13101-GTX 16, and 13074-GTX 18 are a testament to the brand’s commitment to quality and innovation. These tillers are designed to make gardening and landscaping tasks efficient and enjoyable, featuring an array of advanced technologies and characteristics that cater to both novice and seasoned gardeners.

The Troy-Bilt 13101-GTX 16 is engineered for easy operation and maneuverability. Its lightweight design allows users to navigate around gardens effortlessly. Equipped with a robust 16-inch tilling width, it is perfect for small to medium gardening tasks, providing ample coverage without overwhelming the user. The adjustable tilling depth control system ensures that users can achieve the desired soil conditions for various planting needs.

In terms of power, the 13101-GTX 16 is powered by a reliable engine that delivers consistent performance, even in tougher soil conditions. This model also features a gear-driven transmission that allows for smooth operation and better power transfer, ensuring efficient tilling with minimal effort.

The Troy-Bilt 13074-GTX 18 elevates the features found in its 16-inch counterpart, offering a wider 18-inch tilling width. This model is particularly advantageous for larger gardens or plots, allowing users to cover more ground in less time. Moreover, it boasts a heavy-duty build with forged tines that can penetrate even the hardest soil, making it a resilient option for more extensive projects.

Both models incorporate Troy-Bilt’s patented just-a-twist adjustment feature, enabling users to easily switch between forward and reverse tilling directions. This functionality enhances control and versatility, making it easier to navigate around obstacles and till tight spaces.

Another notable feature across these models is the Ergo Handles, designed for comfort and reduced fatigue during extended usage. The cushioned grips provide a secure hold, minimizing vibrations and enhancing user experience.

In summary, the Troy-Bilt 13101-GTX 16, 13101-GTX 16, and 13074-GTX 18 combine user-friendly designs with powerful performance, making them excellent choices for anyone looking to cultivate their green thumb. Whether you are preparing a small flower bed or tilling a larger vegetable garden, these tillers promise reliability, power, and ease, solidifying Troy-Bilt’s reputation as a leading manufacturer in outdoor equipment.
Top Page Image Contents