Troy-Bilt 570 manual Stopping Engine, Gas and Oil Fill-Up, Control Handle, Starting Engine

Page 9

Control Handle

The control handle has three positions. See Figure 4-2.

•FORWARD: Move control handle FORWARD or DOWN to move wedge to split wood.

NOTE: Control handle will return to neutral position as soon as handle is released.(Forward Position only)

•NEUTRAL: Release the control handle or move the lever to neutral position to stop the wedge movement.

•REVERSE: Move control handle BACK or UP to return the wedge toward the cylinder. The control handle stays in the return (Reverse) position and returns to neutral automatically when fully retracted.

NOTE: Reverse position may also be operated back to neutral position manually, if necessary.

Stopping Engine

1.Move throttle control handle to STOP or OFF position.

2.Turn off the engine switch, if so equipped.

3.Disconnect spark plug wire and ground against the engine to prevent unintended starting.

IMPORTANT: Your log splitter may be shipped with motor oil in the engine. You MUST check the oil level before operating. Be careful not to overfill.

To return wedge

Neutral

To stop wedge

To split wood

Figure 4-2

IMPORTANT: Your log splitter is shipped with motor oil in the engine. However, you MUST check the oil level before operating. Be careful not to overfill.

NOTE: Gasoline can be added to the engine when the log splitter is in either the horizontal or vertical position. However, there are less obstructions when the unit is in the vertical position.

4

Operating

Your Log

Splitter

WARNING

Read, understand, and follow all instructions and warnings on the machine and in this

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before

operating.

WARNING: Wear leather work gloves, safety shoes, ear protection, and safety glasses when operating a log splitter. Ensure safe footing.

Gas and Oil Fill-Up

1.Service the engine with gasoline and oil as instructed in the engine manual packed with your log splitter. Read instructions carefully.

WARNING: Use extreme care when han- dling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running.

Starting Engine

1.Attach spark plug wire to spark plug. Make certain the metal cap on the end of the spark plug wire is fastened securely over metal tip of the spark plug.

2.Turn fuel valve, if equipped, to the ON position.

3.Move choke lever, if equipped, to CHOKE position.

4.If the engine is equipped with a primer, follow instructions in the engine manual to prime it.

5.Turn the throttle control handle to the FAST position.

6.Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point).

7.Pull rope with a rapid, full arm stroke. Keep firm grip on starter handle. Let rope rewind slowly. Repeat until engine cranks.

8.After engine starts, move choke lever (if equipped) to OFF position. Place throttle lever to the speed desired.

9.In cold weather, run wedge up or down beam 6 to 8 times to circulate the hydraulic fluid.

WARNING: When starting a warm engine, the muffler and surrounding areas are hot and can cause a burn. Do not touch.

manual before operat- ing.

Wear leather work gloves, safety shoes, ear protection, and safety glasses when operating a log splitter. Ensure safe footing.

Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or run- ning.

When starting a warm engine, the muffler and surrounding areas are hot and can cause a burn. Do not touch.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Log Splitter Model Series MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio25/2006 Finding and Recording Model Number Table of ContentsSafety Labels Found On Your Log Splitter Your Responsibility General PracticesPreparation Operation Maintenance and StorageUse only your hand to operate the controls Do not tow machine faster than 45mphConnecting Cylinder to Beam Setting Up Your Log SplitterAssembling the Tongue Attaching the Jack StandPreparing the Log Splitter Beam Locks Engine Controls Know Your Log SplitterFunction of the controls on the engine Support latch bracket. See FigureGas and Oil Fill-Up Stopping EngineControl Handle Starting EngineUsing the Log Splitter Before Each UseOperating Tips Transporting the Log Splitter Raising and Lowering BeamSplit wood along the grain lengthwise only NeverWedge Assembly Adjustment Gib AdjustmentConditions that Will Void Warranty Adjustment Bolt Jam Nut Gib Lock NutBeam and Splitting Wedge Hydraulic Fluid and Inlet FilterHose Clamps EngineTires Install nylon spider onto engine coupling halfSet Screw Side View-Coupler 0600Replace spark plug Storing Your Log SplitterCause Remedy Problem Cause RemedyService dealer Engine stalls during Low horsepower/weak engineConditions Low horsepower/weak engine RetractingModel Series Service Line at Or visit To order replacementU.S.A Canada MANUFACTURER’S Limited Warranty for

570 specifications

The Troy-Bilt 570 is an exceptional cultivator designed for both amateur and professional gardeners, making tasks like tilling and cultivating soil easy and efficient. With its robust construction and innovative features, it caters to users looking for reliability and performance in their gardening tools.

One of the standout features of the Troy-Bilt 570 is its powerful engine. It typically comes equipped with a dependable 170cc OHV engine, providing ample power to tackle tough soil conditions. The engine is designed for easy starting, which eliminates the frustration often associated with garden equipment. The performance is consistent, even when working in hard or compacted soil, making it a go-to choice for users with demanding gardening needs.

The Troy-Bilt 570 utilizes a counter-rotating tilling technology, which helps in breaking up tough soil and mixing in organic material with greater efficiency. This feature is crucial for promoting healthy plant growth, as it allows for better aeration and nutrient distribution within the soil. With its 16-inch tilling width, the Troy-Bilt 570 can cover large areas in a shorter amount of time, making it ideal for larger gardens or landscaping projects.

Another impressive characteristic of the Troy-Bilt 570 is its adjustable tilling depth. Users can easily modify the depth to meet their specific gardening requirements, whether they are preparing the ground for planting, aerating, or simply mixing in compost. The depth ranges from shallow to deep, allowing for versatility in various gardening tasks.

Ease of use is further enhanced by the cultivator's comfortable, ergonomic grips, which minimize fatigue during extended use. The cultivator also features a lightweight design, making it easy to maneuver around the garden or landscape. Additionally, the Troy-Bilt 570 comes with a variety of attachments, allowing users to customize their gardening experience further, whether it be for weeding, planting, or breaking ground.

In terms of durability, the Troy-Bilt 570 is built with high-quality materials, ensuring it can withstand the rigors of outdoor use over the years. The cultivator is also relatively easy to maintain, with accessible components that simplify repairs and upkeep.

In conclusion, the Troy-Bilt 570 cultivator stands out for its power, versatility, and user-friendly design. Its innovative features and technologies make gardening more efficient and enjoyable, providing gardeners with the tools they need for successful cultivation and landscaping projects.
Top Page Image Contents