Assembling Your Lawn Mower, Tools Required

SECTION 3: ASSEMBLING YOUR LAWN MOWER

To Remove Unit From Carton

•Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.

•Remove loose parts if included with unit (i.e., operator’s manual, etc.).

•Cut along corners and lay carton down flat. Remove packing material. Roll or slide unit out of carton. Check carton thoroughly for loose parts.

NOTE: Parts included for assembly of grass catcher are listed on page 8.

Tools Required

1.Pair of Pliers

2.Funnel

Disconnect Spark Plug Wire

•Before setting up your lawn mower, disconnect the spark plug wire from the spark plug. See Figure 1.

•Attach rubber boot to a bolt on the engine to ground as shown in the figure.

Spark Plug

Rubber Boot

Spark Plug

Wire

Figure 1

IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil before operating your mower.

NOTE: Reference to right or left hand side of the mower is observed from the operating position.

Setting Up Your Lawn Mower

•Remove any packing material which may be between the upper and lower handles for shipping purposes.

•Pull up and back on the upper handle to raise the handle into the operating position. Make certain the lower handle is seated securely into the handle mounting brackets. Tighten the hand knobs on each side of the handle (carriage bolts must be seated properly into the handle). See Figure 2.

Tighten hand knob

Figure 2

NOTE: Your mower is shipped with the handle in the higher height position. If you wish to lower the height of the handle, refer to the Adjustment Section at this time.

•Remove the hairpin clips from the outer hole in the weld pins on the handle mounting brackets. Using a pair of pliers, squeeze one leg of the lower handle against the handle mounting bracket. Insert the hairpin clip into the inner hole on the weld pin. Repeat on the other side. See Figure 3.

Handle Mounting

Bracket

Insert hairpin clip here

Hairpin

Clip

Weld

Figure 3

•The rope guide is attached to the right side of upper handle. Loosen the wing nut which secures the rope guide. See Figure 4.

•With spark plug wire disconnected and grounded, hold the blade control handle against the upper handle, and pull the starter rope out of the engine. Release blade control handle. Slip the rope into the rope guide. Tighten the wing nut. See Figure 4.

•Tighten all nuts and bolts securely.

Slip rope into
rope guide	Wing Nut
	Wing Nut

Rope

Guide

Figure 4

LC-436 specifications

The White Outdoor LC-436 is a robust lawn mower that has made a notable impact in the outdoor power equipment market. This versatile machine is designed to meet the varying needs of lawn care enthusiasts, featuring a combination of efficiency, reliability, and user-friendly operation.

One of the main features of the White Outdoor LC-436 is its powerful engine. Equipped with a reliable four-stroke engine, it delivers dependable performance and ensures optimal cutting power. The engine enables the mower to tackle thick grass and uneven terrain with ease, making it an ideal choice for homeowners with expansive yards or challenging landscapes.

The cutting deck of the LC-436 is another highlight of its design. With a generous 21-inch cutting width, this mower can cover a large area in a shorter amount of time. The deck is crafted from high-quality materials, ensuring durability and longevity while also providing a clean cut. Users can easily adjust the cutting height to achieve their desired lawn finish, giving them complete control over their mowing experience.

The LC-436 also incorporates advanced technologies that enhance its performance and ease of use. One notable feature is the self-propulsion system, which allows users to mow with minimal physical effort. This technology is particularly beneficial for larger properties or slopes, as it provides consistent speed and reduces fatigue during long mowing sessions.

In addition to its powerful engine and cutting capabilities, the mower is designed with user comfort in mind. Ergonomically designed handles and vibration-dampening features help reduce operator strain, making it more enjoyable to use for extended periods. The mower's lightweight construction adds to its maneuverability, allowing users to navigate tight corners and garden beds effortlessly.

Fuel efficiency is another characteristic that sets the White Outdoor LC-436 apart from its competitors. The four-stroke engine is engineered for optimal fuel consumption, enabling users to mow their lawns without excessive fuel costs, thereby providing an economical choice for regular maintenance.

In summary, the White Outdoor LC-436 stands out as a high-performing lawn mower, complete with a powerful engine, adjustable cutting deck, and user-friendly features designed for comfort and efficiency. Its blend of innovative technologies and robust construction makes it a reliable choice for homeowners seeking a dependable solution for maintaining their outdoor spaces. Whether it’s for occasional use or routine lawn care, the LC-436 is engineered to deliver a superior mowing experience.