OFF-SEASON Storage, Cleaning the Tine Area, Tires

Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air circulation which is essential to engine performance and life. Be certain to remove all dirt and combustible debris from muffler area.

CLEANING THE TINE AREA

Clean the underside of the tine shield after each use. The dirt washes off the tines easier if rinsed off immediately instead of after it dries. Always towel dry the tiller afterwards and apply a light coat of oil or silicone to prevent rusting or water damage.

IMPORTANT: Never use a "pressure" washer to clean your tiller. Water can penetrate tight areas of the tiller and its chaincase and cause serious damage to the unit.

TIRES

Recommended operating tire pressure is approximately 14 p.s.i. on 14 inch tires and 20 p.s.i. on 16 inch tires. (Check sidewall of tire for tire manufacturer’s recommended pressure). Maximum tire pressure under any circumstances is 30 p.s.i.

If belt replacement is required, order belt or belts by part number from your nearest authorized dealer.

Part No. 754-0438—‘‘V’’ Belt

1.Disconnect and ground the spark plug wire against the engine.

2.Remove the belt cover from the left side of the tiller as follows:

•Remove two torx head screws from the top of belt cover.

•Remove two hex cap nuts and flat washers from front side of the belt cover. Remove the hex nut and flat washer at the back of the cover.

3.Remove the belt keeper assembly located behind the engine pulley by removing two hex bolts and lock washers. See Figure 14.

4.Remove belt. Reassemble new belt, following instructions in reverse order.

NOTE: Upon reassembly, make certain the belt is routed over the idler pulley and inside of belt keepers by engine pulley. See Figure 14.

Engine

Equal tire pressure should be maintained on both tires.

When installing a tire to the rim, be certain rim is clean and free of rust. Lubricate both the tire and rim generously. Never inflate to over 30 p.s.i. to seat beads.

WARNING: Excessive pressure (over 30 p.s.i.) when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury.

BELT REPLACEMENT

Pulley

Belt Keeper

Hex Bolts

CAUTION: Do not use an off-the-shelf belt.

Your tiller has been engineered with a belt made of special material (Kevlar Tensile) for longer life and better performance. It should not be replaced with an off-the-shelf belt.

BeltIdler

Keeper Pulley

Figure 14

SECTION 11: OFF-SEASON STORAGE

If the tiller will not be used for a period longer than 30 days, the following steps should be taken to prepare the tiller for storage.

1.Clean the exterior of engine and the entire tiller thoroughly. Lubricate the tiller as described in the lubrication instructions.

2.Refer to the engine manual for correct engine storage instructions.

3.Wipe tines with oiled rag to prevent rust.

4.Store tiller in a clean, dry area. Do not store next to corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any springs, bearings and cables.

414 specifications

White 414 is a renowned model in the landscape of industrial machinery, particularly known for its innovative features and robust technologies. This machine has made significant strides in enhancing productivity and efficiency in various sectors, including construction, forestry, and agriculture.

One of the main features of White 414 is its powerful engine, which is designed for optimal performance and fuel efficiency. The engine is capable of delivering substantial horsepower, allowing it to handle demanding tasks effortlessly. Alongside this, the engine’s advanced design ensures reduced emissions, aligning with contemporary environmental standards.

The White 414 is also equipped with a state-of-the-art hydraulic system, which plays a crucial role in its operational capabilities. This hydraulic system enhances the machine's responsiveness and allows for smooth operation under varying loads. The agility of the hydraulic system makes it suitable for a wide range of applications, from lifting heavy materials to precision tasks requiring finely tuned control.

Another standout characteristic of the White 414 is its durability and rugged construction. Built with high-quality materials, the machine is designed to withstand the rigors of intensive use in challenging environments. This durability not only extends the lifespan of the equipment but also reduces maintenance costs, making it a smart investment for businesses.

Moreover, the White 414 features an ergonomic design that prioritizes the operator's comfort and safety. The cab is spacious, equipped with advanced control systems, and provides excellent visibility, ensuring that operators can perform their tasks safely and efficiently. Safety features such as rollover protection and advanced braking systems are integrated into the design, promoting a secure working environment.

In addition to these features, the White 414 is compatible with a wide array of attachments and accessories. This versatility allows operators to customize the machine for specific tasks, enhancing its functionality across various industries. Whether it's fitted with a bucket, fork, or grader, the White 414 adapts to the job at hand with ease.

In summary, the White 414 stands out for its powerful performance, advanced hydraulic system, rugged build quality, ergonomic design, and versatility. These characteristics make it a valuable asset for professionals in multiple fields, ensuring they can accomplish their projects efficiently and effectively. As industries continue to evolve, the White 414 remains a trusted choice among operators seeking reliability and performance in their equipment.