Trouble-shooting

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-877-897-7493, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check to see if the GFCI breaker is tripped or was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR THE GFCI TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker or the GFCI. If the cir- cuit breaker or the GFCI trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter from the filter housing and clean or replace the filter (see page 13).

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department.

c.The pump may have a loose wire connection. Contact our customer service department.

4.SYMPTOM: THE PUMP HUMS, BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department. If your spa is no longer under warranty, contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department.

b.The pump may have a bad bearing. Contact our customer service department.

6.SYMPTOM: THE WATER DOES NOT HEAT

a.Make sure that the hydrotherapy spa is fully covered with the spa cover. The spa cover must be tight for the water to heat. Set the air control to low. The water will heat at a rate of 6°F per hour. If you are using the spa indoors and the room temperature is main-

tained at 70°F, it will take approximately 6 to 8 hours for the water to reach the set temperature.

b. If you are using the hydrotherapy spa outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air Temperature	Heating Time
70°F +	6 to 8 hours
50°F to 70°F	9 to 11 hours
30°F to 50°F	12 to 14 hours

b. If the water still has not heated after 24 hours, contact our customer service department.

7.SYMPTOM: THE WATER IS NOT BEING CLEANED BY THE FILTER

a.Check to see if the filter is in place. Clean the filter if it is dirty.

b.Check the chemical balance of the water. If the pH is incorrect, the sanitizing agents will not function properly. See the section on maintain- ing the proper pH balance on page 14.

8.SYMPTOM: THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW

a.This usually occurs only when the water level is low. Add water until it is 2 to 4” above the skim- mer basket.

9.SYMPTOM: THE WATER LEVEL DROPS

a.A clamp or seal inside the pump compartment may be loose. Check inside the pump compart- ment for excess water and watch the pump unit while it is operating to see if water drips from any of the plumbing. If you can identify the location of the leak inside the spa jet unit, tight- en the clamp or replace the damaged seal.

b.Some water loss due to evaporation is normal. If rapid water loss occurs, or if you notice wet- ness on the floor around the hydrotherapy spa, the spa shell may have a leak. Contact your local pool and spa service provider for repairs.

WLSB62810, WLSG62810 specifications

The Weslo WLSG62810 and WLSB62810 treadmills are two popular models designed for home fitness enthusiasts who appreciate a blend of performance, convenience, and affordability. Both treadmills offer a range of features and technologies that make them suitable for beginners and intermediate users looking to enhance their cardiovascular health and overall fitness.

One of the standout characteristics of the Weslo WLSG62810 is its space-saving design. The treadmill features a folding mechanism that allows users to easily store it away when not in use, making it an excellent choice for those with limited workout space. The sturdy construction ensures stability during workouts, accommodating users of various weights and sizes.

The WLSG62810 is equipped with a powerful motor that delivers smooth and consistent performance, allowing users to experience speeds ranging from 0 to 10 miles per hour. This feature is ideal for a range of workout styles, from brisk walking to high-intensity running. The 2-ply treadmill belt provides a comfortable surface that reduces impact on the joints, making it suitable for users looking for low-impact exercise options.

In addition, the Weslo WLSB62810 also shares similar motor specifications and speed capacities. Both models come with a user-friendly LCD display that tracks essential workout metrics, including time, distance, speed, and calories burned. This information is crucial for users who wish to monitor their progress and stay motivated throughout their fitness journey.

Another significant feature of these treadmills is the built-in workout programs. The WLSG62810 offers a variety of pre-set workouts designed by certified trainers to suit different fitness levels and goals. This feature provides users with guidance and structure, helping them to remain engaged and challenged as they progress.

Weslo treadmills are also designed with user comfort in mind. Both models are equipped with adjustable incline settings, allowing users to simulate outdoor terrains and increase the intensity of their workouts. Alongside this, the cushioned deck technology minimizes impact, enhancing comfort during exercise.

Lastly, the compact size and lightweight build of both models make them easy to move around the home, facilitating workouts in various locations. With their thoughtful design, technology, and user-friendly features, the Weslo WLSG62810 and WLSB62810 treadmills are excellent additions to any home gym. They are perfect for anyone seeking an accessible way to achieve their fitness goals and maintain an active lifestyle.