Woods Equipment TC68, TCR60, TCR68, TCR74, TC74 Safety Rules, Training, Preparation, Operation

Page 5

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.

In addition to the design and configuration of equipment, hazard control and accident preven- tion are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.

It has been said “The best safety device is an informed, careful operator.” We ask you to be that kind of operator.

TRAINING

„Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replace- ment manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319- 6637.) Failure to follow instructions or safety rules can result in serious injury or death.

„If you do not understand any part of this manual and need assistance, see your dealer.

„Know your controls and how to stop engine and attachment quickly in an emergency.

„Operators must be instructed in and be capable of the safe operation of the equipment, its attach- ments, and all controls. Do not allow anyone to operate this equipment without proper instruc- tions.

„Never allow children or untrained persons to operate equipment.

PREPARATION

„Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

„Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

„Make sure attachment is properly secured, adjusted, and in good operating condition.

„Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

„Before putting equipment into service, check and adjust driveline length as instructed in Opera- tor's Manual. Driveline must not bottom out or pull apart throughout the full range of the tractor hitch. Do not operate until driveline length is correct.

„Before starting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drive- lines, repair and replace bearings before putting equipment into service.

„Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times.

„Remove accumulated debris from this equip- ment, power unit, and engine to avoid fire hazard.

„Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

„Make sure shields and guards are properly installed and in good condition. Replace if dam- aged.

„A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up result- ing in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

„Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.

OPERATION

„Only engage power when equipment is at ground operating level. Always disengage power when equipment is raised off the ground.

„Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

(Safety Rules continued on next page)

TS(R) SR (3/2/2012)

Safety 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Rotary Tillers To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Rules SafetyTraining PreparationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsTo Avoid Serious Injury or Death Be CarefulOperation OperationShortening Driveline Driveline AttachmentTiller Side Shift Adjustment Working Depth AdjustmentRear Shield Adjustment Operating ProcedureTractor Stability Clutch Run-InPRE-OPERATION Check List Operating TechniquesBlocking Method Owner ServiceOwner Service Qualified Technician Maintenance Gearbox Lubrication Chain MaintenanceLubrication Information PTO Drive LinesCleaning Slip Clutch AdjustmentDriveline Shear Bolt Replacement Four Blade Installation Blade InstallationTrouble Shooting Dealer Service Dealer ServiceGearbox Maintenance Seal ReplacementOutput Hollow Shaft Repair Input Shaft RepairUniversal Joint Repair Joint DisassemblyInstall Cups Joint AssemblyAssembly AssemblyAssembly Procedures SET-UP InstructionsCrate Assembly Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Rotary TillersTC60/TCR60 Rotary Tiller Assembly Hhcs TC68/TCR68 Rotary Tiller Assembly 103183668 TC74/TCR74 Rotary Tiller Assembly 103183674 Part QTY Description Comer Slip Clutch Drive AssemblyComer Shear Bolt Drive Assembly Optional Gearbox Assembly SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart AppendixAbbreviations Bolt Size ChartWarranty Rev /3/2011

TC68, TC60, TC74, TCR74, TCR68 specifications

Woods Equipment has established a reputation for producing high-quality agricultural and landscaping equipment, and their line of TCR and TC series implements exemplifies this commitment to quality and performance. The TCR68, TCR74, TCR60, TC60, and TC68 models are notable products within this range, tailored to meet the diverse needs of operators in various situations.

The TCR series, including the TCR68 and TCR74, is designed as a compact rotary cutter that efficiently handles heavy grass and brush. One of the standout features of the TCR series is its robust construction, incorporating a durable steel frame and high-performance blades that make it highly effective in dense growth areas. The TCR models are equipped with a flexible hitch system, allowing for easy attachment to a range of tractors, delivering exceptional maneuverability while enhancing productivity on any job site.

The TCR68, known for its 68-inch cutting width, is perfect for medium-sized properties, providing an excellent balance between size and power. Conversely, the TCR74 with a 74-inch width caters to larger open areas, ensuring fewer passes are needed for efficiency. Both models feature a maximum cutting height adjustment, catering to the specific needs of users for different types of landscaping jobs.

The TC series, which includes the TC60 and TC68, takes versatility to the next level. These models serve as versatile tillage tools. The TC60 features a 60-inch working width, making it ideal for smaller gardens and farms. Built with a robust frame and quality components, it ensures long-lasting performance. The TC68 model offers an increased working width of 68 inches, appealing to larger landowners who require fast and efficient soil preparation.

Both TC models emphasize ease of use, with user-friendly adjustments for depth and tilling intensity. They feature advanced technologies such as automatic depth control, ensuring consistent tillage results across varying soil conditions.

In conclusion, whether choosing the TCR series for cutting or the TC series for tilling, Woods Equipment provides reliable and effective solutions. These models combine advanced engineering, durable materials, and innovative features, positioning them as go-to implements for agricultural and landscaping professionals alike. Their commitment to performance and reliability continues to make Woods Equipment a trusted name in the industry.
Top Page Image Contents