Woods Equipment TCR60, TCR68, TCR74, TC74, TC60, TC68 manual Maintenance

Page 6

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

„Keep bystanders away from equipment.

„Never direct discharge toward people, animals, or property.

„Do not operate equipment while under the influ- ence of alcohol or drugs.

„Operate only in daylight or good artificial light.

„Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

„Always comply with all state and local lighting and marking requirements.

„Never allow riders on power unit or attachment.

„Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times.

„Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

„Operate tractor PTO at 540 RPM. Do not exceed.

„Do not operate PTO during transport.

„Connect PTO driveline directly to power unit PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

„Look down and to the rear and make sure area is clear before operating in reverse.

„Use extreme care when working close to fences, ditches, other obstructions, or on hillsides.

„Do not operate or transport on steep slopes.

„Do not stop, start, or change directions sud- denly on slopes.

„Use extreme care and reduce ground speed on slopes and rough terrain.

„Watch for hidden hazards on the terrain during operation.

„Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

„Before performing any service or maintenance, disconnect driveline from tractor PTO.

„Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pres- sure, set parking brake, stop engine, remove key, and unfasten seat belt.

„Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

MAINTENANCE

„Service and maintenance work not covered in OWNER SERVICE must be done by a qualified dealership. Special skills, tools, and safety proce- dures may be required. Failure to follow these instructions can result in serious injury or death.

„Before performing any service or maintenance, disconnect driveline from tractor PTO.

„Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pres- sure, set parking brake, stop engine, remove key, and unfasten seat belt.

„Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

6Safety

TS(R) SR (3/2/2012)

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Rotary Tillers Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationTraining SafetySafety Rules PreparationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedBe Careful To Avoid Serious Injury or DeathOperation OperationDriveline Attachment Shortening DrivelineWorking Depth Adjustment Tiller Side Shift AdjustmentTractor Stability Operating ProcedureRear Shield Adjustment Clutch Run-InOperating Techniques PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Lubrication Information Chain MaintenanceQualified Technician Maintenance Gearbox Lubrication PTO Drive LinesSlip Clutch Adjustment Driveline Shear Bolt ReplacementCleaning Blade Installation Four Blade InstallationTrouble Shooting Gearbox Maintenance Dealer ServiceDealer Service Seal ReplacementInput Shaft Repair Output Hollow Shaft RepairJoint Disassembly Universal Joint RepairJoint Assembly Install CupsAssembly Procedures AssemblyAssembly SET-UP InstructionsCrate Assembly PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListRotary Tillers PartsTC60/TCR60 Rotary Tiller Assembly Hhcs TC68/TCR68 Rotary Tiller Assembly 103183668 TC74/TCR74 Rotary Tiller Assembly 103183674 Comer Slip Clutch Drive Assembly Part QTY DescriptionComer Shear Bolt Drive Assembly Optional Gearbox Assembly Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart AppendixBolt Size Chart AbbreviationsWarranty Rev /3/2011

TC68, TC60, TC74, TCR74, TCR68 specifications

Woods Equipment has established a reputation for producing high-quality agricultural and landscaping equipment, and their line of TCR and TC series implements exemplifies this commitment to quality and performance. The TCR68, TCR74, TCR60, TC60, and TC68 models are notable products within this range, tailored to meet the diverse needs of operators in various situations.

The TCR series, including the TCR68 and TCR74, is designed as a compact rotary cutter that efficiently handles heavy grass and brush. One of the standout features of the TCR series is its robust construction, incorporating a durable steel frame and high-performance blades that make it highly effective in dense growth areas. The TCR models are equipped with a flexible hitch system, allowing for easy attachment to a range of tractors, delivering exceptional maneuverability while enhancing productivity on any job site.

The TCR68, known for its 68-inch cutting width, is perfect for medium-sized properties, providing an excellent balance between size and power. Conversely, the TCR74 with a 74-inch width caters to larger open areas, ensuring fewer passes are needed for efficiency. Both models feature a maximum cutting height adjustment, catering to the specific needs of users for different types of landscaping jobs.

The TC series, which includes the TC60 and TC68, takes versatility to the next level. These models serve as versatile tillage tools. The TC60 features a 60-inch working width, making it ideal for smaller gardens and farms. Built with a robust frame and quality components, it ensures long-lasting performance. The TC68 model offers an increased working width of 68 inches, appealing to larger landowners who require fast and efficient soil preparation.

Both TC models emphasize ease of use, with user-friendly adjustments for depth and tilling intensity. They feature advanced technologies such as automatic depth control, ensuring consistent tillage results across varying soil conditions.

In conclusion, whether choosing the TCR series for cutting or the TC series for tilling, Woods Equipment provides reliable and effective solutions. These models combine advanced engineering, durable materials, and innovative features, positioning them as go-to implements for agricultural and landscaping professionals alike. Their commitment to performance and reliability continues to make Woods Equipment a trusted name in the industry.
Top Page Image Contents