Shredding Material, Operating Technique

SHREDDING MATERIAL

For shredding, set the cutter lower at rear. Determine how much lower to set the rear by experimenting in dif- ferent situations.

OPERATING TECHNIQUE

1.Power for operating the cutter is supplied by the tractor PTO. Operate PTO at 540 rpm. Know how to stop the tractor and cutter quickly in an emergency.

2.Engage PTO at a low engine rpm to minimize stress on the drive system and gearbox. With PTO engaged, raise PTO speed to 540 rpm and maintain throughout cutting operation.

Gearbox protection is provided by a slip clutch with replacement fiber disc or a shear bolt. The slip clutch is designed to slip and the shear bolt will shear when excessive torsion loads occur.

3.Move slowly into material. Adjust tractor ground speed to provide a clean cut without lugging the tractor engine. Use a slow ground speed for better shredding.

Proper ground speed will depend on the terrain and the material’s height, type, and density.

Normally, ground speed will range from 2 to 5 mph. Tall, dense material should be cut at a low speed; thin, medium-height material can be cut at a faster ground speed.

4.Always operate tractor PTO at 540 rpm to maintain proper blade speed and to produce a clean cut.

5.Under certain conditions tractor tires may roll down some grass and prevent cutting at the same height as the surrounding area. When this occurs, reduce your ground speed but maintain PTO at 540 rpm. The lower ground speed will permit grass to rebound partially.

STORAGE

Disconnect cutter driveshaft and secure up off ground. Raise cutter with 3-point hitch. Place blocks under cutter side skids. Lower cutter onto blocks. Disconnect cutter from tractor 3-point hitch and carefully drive tractor away from cutter.

Keep children and bystanders away from stor- age area.

PRE-OPERATION CHECK LIST

OWNER’S RESPONSIBILITY

___ Review and follow all safety rules and safety decal instructions on page 7 through page 11.

___ Check that equipment is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin or collar slides freely and is seated firmly in trac- tor PTO spline groove.

___ Set tractor PTO at 540 rpm.

___ Lubricate all grease fitting locations. Make sure PTO shaft slip joint is lubricated.

___ Check to be sure gear lube runs out the small check plug on side of gearbox.

___ Check that all hardware is properly installed and secured.

___ Check that blades are sharp and secure and cut- ting edge is positioned to lead in a counterclock- wise rotation.

___ Check that shields and guards are properly installed and in good condition. Replace if dam- aged.

___ Check cutting height, front-to-rear attitude, and top link adjustment.

___ Place tractor PTO and transmission in neutral before starting engine.

___ Inspect area to be cut and remove stones, branches, or other hard objects that might be thrown and cause injury or damage.

MAN0670 (11/16/2007)	Operation 17

HC60, HC72, HC48, HC54 specifications

Woods Equipment Company is a renowned manufacturer of high-quality agricultural and landscape equipment, and their line of hydraulic cutters is no exception. The Woods HC series, which includes the HC48, HC54, HC60, and HC72 models, is designed for efficiency and versatility in various applications, making them ideal for landscapers, farmers, and contractors.

One of the main features of Woods HC series cutters is their robust construction. These machines are built with high-strength materials, ensuring durability and longevity even in tough working conditions. The frames are designed to withstand significant stresses while providing stability during operation.

A standout characteristic of the HC series is its cutting capabilities. Each model is equipped with heavy-duty blades that are engineered to handle tough vegetation, including small trees, thick brush, and dense undergrowth. The cutting width increases with each model, ranging from 48 inches in the HC48 to 72 inches in the HC72, providing options for various land clearing tasks.

Another notable feature is the hydraulic drive system. This technology allows for smooth operation and precise control of cutting speed, improving overall efficiency. The hydraulic system is designed for optimal performance, ensuring that users can tackle even the most challenging jobs with ease.

The HC series also incorporates a user-friendly design. The implements are easy to attach and detach from tractors, facilitating quick transitions between different tasks. Woods has addressed safety concerns by integrating protective shielding around the cutting area, which minimizes the risk of debris being thrown during operation.

For ease of maintenance, the HC series models come with easily accessible service points, allowing operators to perform routine checks and maintenance without hassle. This feature contributes to the longevity of the equipment, ensuring that owners maximize their investment.

Compatibility is another essential advantage of the Woods HC series. Designed to work seamlessly with a variety of tractors, these cutters allow for flexibility across different tractor brands and models, making them a versatile choice for operators with mixed equipment lines.

In summary, Woods Equipment HC48, HC54, HC60, and HC72 hydraulic cutters stand out for their robust construction, cutting efficiency, hydraulic drive, user-friendly features, and compatibility with various tractors. These models are perfect for anyone looking to maintain their land effectively, making challenging cutting tasks accessible and manageable. Overall, the HC series is a reliable investment for professional land management needs.