Woods Equipment HC54, HC48, HC72, HC60 manual Blade Sharpening, Slip Clutch Adjustment

Page 20

3.Align crossbar (8) with blade access hole in cutter frame. Apply a liberal coating of Never Seez® or equivalent to blade pin and crossbar hole. Make sure blade offset is away from cutter. Push blade pin through crossbar.

4.Insert lock washer (15) and nut (14) through blade access hole in the cutter frame. Install on blade pin

(12)and tighten to 450 lbs-ft using a 1-11/16" socket.

Blade Sharpening

NOTICE

Closely inspect blades for cracks or nicks, replace damaged blades in sets.

When sharpening blades, grind the same amount on each blade to maintain balance. Replace blades in pairs. Unbalanced blades will cause excessive vibration, which can damage gearbox bearings. Vibration may also cause struc- tural cracks to cutter.

1.Sharpen both blades at the same time to maintain balance. Follow original sharpening pattern.

2.Do not sharpen blade to a razor edge—leave at least a 1/16" blunt edge.

3.Do not sharpen back side of blade.

Figure 13. Blade Sharpening

SLIP CLUTCH ADJUSTMENT

The slip clutch is designed to slip so that the gearbox and driveline are protected if the cutter strikes an obstruction.

A new slip clutch or one that has been in storage over the winter may seize. Before operating the cutter, make sure it will slip by performing the following operation:

1.Turn off tractor engine and remove key.

2.Loosen nuts on springs until the springs can rotate freely, yet remain secure on the bolts.

3.Mark outer plates of slip-disc clutch as shown in Figure 14.

4.Securely attach implement to the tractor and start the tractor.

5.Engage PTO for several seconds then quickly disengage it.

6.Turn tractor off and remove key.

7.The friction lining plates should have "slipped". Check the marks placed on the outer plates of the slip-disc clutch in step 3 to make sure this is the case.

8.If clutch does not slip, check assembly for oil, grease and debris. Clean if necessary.

9.Reassemble clutch and tighten bolts no more than 1/8 of a turn at a time until desired setting of 1.26" is reached as shown in Figure 14.

10.If excessive slippage continues, check lining plates for excessive wear. They are 1/8" thick when new and should be replaced after 1/32" of wear to ensure proper operation.

Figure 14. Slip Clutch Assembly

20 Owner Service

MAN0670 (11/16/2007)

 

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Heritagetm Introduction To the DealerTable of Contents Specifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules TrainingPreparation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedBe Careful Crushing and Pinching HazardOperation OperationTractor Stability Attach Cutter to TractorTop Link Adjustment Quick Hitch Assembly HC48 / HC54Quick Hitch Quick Hitch Assembly HC60 / HC72Standard Hitch Driveline Installation Tractor PTO To InstallDriveline Adjustment To RemoveCutting Height Adjustment Driveline Interference CheckPRE-OPERATION Check List Shredding MaterialOperating Technique Owner Service Owner ServiceBlocking Method Lubrication InformationBlade Removal Blade InstallationBlade Servicing Slip Clutch Adjustment Blade SharpeningShielding Repair Driveline Shear Bolt ReplacementCleaning Mowing Conditions TroubleshootingTroubleshooting Dealer Service Dealer ServiceGearbox Maintenance Seal ReplacementGearbox Repair Flat TOP Figure Disassemble Gearbox Vertical Shaft Repair Flat Top FigureHorizontal Leak Repair Flat Top Figure Gearbox Assembly Flat Top Gearbox Reassemble GearboxReinstall Gearbox Gearbox RepairOn CAST/CROWN TOP Figure Vertical Shaft Repair Cast/Crown TopGearbox Assembly Cast/Crown Top Gearbox Crossbar RemovalCrossbar Installation Crossbar RemovalJoint Disassembly Universal Joint RepairJoint Assembly Remove CupsDealer SET-UP Instructions AssemblyAssembly Install Driveline Disassemble Shipping UnitAssemble Cutter Shear Bolt DrivelineInstall Safety Shielding Driveline Slip ClutchFill Gearbox Rubber DeflectorDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListHeritageTM PartsHC48, HC54, HC60, HC72 Assembly HC48, HC54, HC60, HC72 Assembly Parts List Part QTY DescriptionGearbox Assembly Flat TOP NSSGearbox Assembly CAST/CROWN TOP Ball BearingHC48 Shear Bolt Driveline Assembly HC54, HC60, HC72 Shear Bolt Driveline Assembly HC48, HC54, HC60 Slip Clutch Driveline Assembly Optional HC72 Slip Clutch Driveline Assembly Front Rubber Shielding Standard Front & Rear Chain Shielding Optional QTY Part DescriptionQuick Hitch Hardware Optional Bolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexMAN0670 11/16/2007 Index Warranty Rev /14/2011 Warranty

HC60, HC72, HC48, HC54 specifications

Woods Equipment Company is a renowned manufacturer of high-quality agricultural and landscape equipment, and their line of hydraulic cutters is no exception. The Woods HC series, which includes the HC48, HC54, HC60, and HC72 models, is designed for efficiency and versatility in various applications, making them ideal for landscapers, farmers, and contractors.

One of the main features of Woods HC series cutters is their robust construction. These machines are built with high-strength materials, ensuring durability and longevity even in tough working conditions. The frames are designed to withstand significant stresses while providing stability during operation.

A standout characteristic of the HC series is its cutting capabilities. Each model is equipped with heavy-duty blades that are engineered to handle tough vegetation, including small trees, thick brush, and dense undergrowth. The cutting width increases with each model, ranging from 48 inches in the HC48 to 72 inches in the HC72, providing options for various land clearing tasks.

Another notable feature is the hydraulic drive system. This technology allows for smooth operation and precise control of cutting speed, improving overall efficiency. The hydraulic system is designed for optimal performance, ensuring that users can tackle even the most challenging jobs with ease.

The HC series also incorporates a user-friendly design. The implements are easy to attach and detach from tractors, facilitating quick transitions between different tasks. Woods has addressed safety concerns by integrating protective shielding around the cutting area, which minimizes the risk of debris being thrown during operation.

For ease of maintenance, the HC series models come with easily accessible service points, allowing operators to perform routine checks and maintenance without hassle. This feature contributes to the longevity of the equipment, ensuring that owners maximize their investment.

Compatibility is another essential advantage of the Woods HC series. Designed to work seamlessly with a variety of tractors, these cutters allow for flexibility across different tractor brands and models, making them a versatile choice for operators with mixed equipment lines.

In summary, Woods Equipment HC48, HC54, HC60, and HC72 hydraulic cutters stand out for their robust construction, cutting efficiency, hydraulic drive, user-friendly features, and compatibility with various tractors. These models are perfect for anyone looking to maintain their land effectively, making challenging cutting tasks accessible and manageable. Overall, the HC series is a reliable investment for professional land management needs.
Top Page Image Contents