Woods Equipment HC54, HC48, HC72, HC60 manual Operation, Tractor Stability, Attach Cutter to Tractor

Page 12

OPERATION

The operator is responsible for the safe operation of the cutter. The operator must be properly trained. Operators should be familiar with the cutter, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on page 7 through page 11. Be sure to complete the Pre-Operation check list on page 17 before operating this cutter.

This standard-duty cutter is designed for grass and weed mowing and shredding.

Recommended mowing speed for most conditions is from 2 to 5 mph.

Full chain, rubber, or steel band shielding must be installed when operating in populated areas or other areas where thrown objects could injure peo- ple or damage property.

•If this machine is not equipped with full chain, rubber, or steel band shielding, operation must be stopped when anyone comes within 300 feet (92 m).

•This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

CAUTION

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

TRACTOR STABILITY

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up result- ing in loss of steering. The weight may be attained

with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

Figure 1. Tractor Stability

ATTACH CUTTER TO TRACTOR

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

Keep bystanders away from equipment.

Operate tractor PTO at 540 RPM. Do not exceed.

CAUTION

Make sure driveline will not bottom out at the shortest length and that it has at least 1/3 overlap at the longest length.

With cutter adjusted to transport position, set upper stop on tractor lift quadrant to prevent deck from hitting the driveline when being raised.

Select a top link mounting pin (maximum length 3-5/8") that will allow floating link to swing freely through the cutter A-frame bars.

1.Attach tractor 3-point lift arms to the cutter hitch pins and secure.

2.Attach tractor top link to cutter clevis using forward hole. Select a top link mounting pin that will allow floating link to swing freely through the cutter A- frame bars.

NOTE: You will need to adjust the top link; refer to Top Link Adjustment, page 13.

3.Adjust the tractor lower 3-point arm anti-sway devices to prevent cutter from swinging side to side during transport.

4.Adjust tractor drawbar so that it will not interfere with cutter or driveline.

12 Operation

MAN0670 (11/16/2007)

 

 

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Heritagetm Introduction To the DealerTable of Contents Specifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules TrainingPreparation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedBe Careful Crushing and Pinching HazardOperation OperationTractor Stability Attach Cutter to TractorTop Link Adjustment Quick Hitch Assembly HC48 / HC54Quick Hitch Assembly HC60 / HC72 Standard HitchQuick Hitch Driveline Installation Tractor PTO To InstallDriveline Adjustment To RemoveCutting Height Adjustment Driveline Interference CheckShredding Material Operating TechniquePRE-OPERATION Check List Owner Service Owner ServiceBlocking Method Lubrication InformationBlade Installation Blade ServicingBlade Removal Slip Clutch Adjustment Blade SharpeningDriveline Shear Bolt Replacement CleaningShielding Repair Troubleshooting TroubleshootingMowing Conditions Dealer Service Dealer ServiceGearbox Maintenance Seal ReplacementVertical Shaft Repair Flat Top Figure Horizontal Leak Repair Flat Top FigureGearbox Repair Flat TOP Figure Disassemble Gearbox Gearbox Assembly Flat Top Gearbox Reassemble GearboxReinstall Gearbox Gearbox RepairOn CAST/CROWN TOP Figure Vertical Shaft Repair Cast/Crown TopGearbox Assembly Cast/Crown Top Gearbox Crossbar RemovalCrossbar Installation Crossbar RemovalJoint Disassembly Universal Joint RepairJoint Assembly Remove CupsAssembly AssemblyDealer SET-UP Instructions Install Driveline Disassemble Shipping UnitAssemble Cutter Shear Bolt DrivelineInstall Safety Shielding Driveline Slip ClutchFill Gearbox Rubber DeflectorDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListHeritageTM PartsHC48, HC54, HC60, HC72 Assembly HC48, HC54, HC60, HC72 Assembly Parts List Part QTY DescriptionGearbox Assembly Flat TOP NSSGearbox Assembly CAST/CROWN TOP Ball BearingHC48 Shear Bolt Driveline Assembly HC54, HC60, HC72 Shear Bolt Driveline Assembly HC48, HC54, HC60 Slip Clutch Driveline Assembly Optional HC72 Slip Clutch Driveline Assembly Front Rubber Shielding Standard Front & Rear Chain Shielding Optional QTY Part DescriptionQuick Hitch Hardware Optional Bolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexMAN0670 11/16/2007 Index Warranty Rev /14/2011 Warranty

HC60, HC72, HC48, HC54 specifications

Woods Equipment Company is a renowned manufacturer of high-quality agricultural and landscape equipment, and their line of hydraulic cutters is no exception. The Woods HC series, which includes the HC48, HC54, HC60, and HC72 models, is designed for efficiency and versatility in various applications, making them ideal for landscapers, farmers, and contractors.

One of the main features of Woods HC series cutters is their robust construction. These machines are built with high-strength materials, ensuring durability and longevity even in tough working conditions. The frames are designed to withstand significant stresses while providing stability during operation.

A standout characteristic of the HC series is its cutting capabilities. Each model is equipped with heavy-duty blades that are engineered to handle tough vegetation, including small trees, thick brush, and dense undergrowth. The cutting width increases with each model, ranging from 48 inches in the HC48 to 72 inches in the HC72, providing options for various land clearing tasks.

Another notable feature is the hydraulic drive system. This technology allows for smooth operation and precise control of cutting speed, improving overall efficiency. The hydraulic system is designed for optimal performance, ensuring that users can tackle even the most challenging jobs with ease.

The HC series also incorporates a user-friendly design. The implements are easy to attach and detach from tractors, facilitating quick transitions between different tasks. Woods has addressed safety concerns by integrating protective shielding around the cutting area, which minimizes the risk of debris being thrown during operation.

For ease of maintenance, the HC series models come with easily accessible service points, allowing operators to perform routine checks and maintenance without hassle. This feature contributes to the longevity of the equipment, ensuring that owners maximize their investment.

Compatibility is another essential advantage of the Woods HC series. Designed to work seamlessly with a variety of tractors, these cutters allow for flexibility across different tractor brands and models, making them a versatile choice for operators with mixed equipment lines.

In summary, Woods Equipment HC48, HC54, HC60, and HC72 hydraulic cutters stand out for their robust construction, cutting efficiency, hydraulic drive, user-friendly features, and compatibility with various tractors. These models are perfect for anyone looking to maintain their land effectively, making challenging cutting tasks accessible and manageable. Overall, the HC series is a reliable investment for professional land management needs.
Top Page Image Contents