Push Channel Attachment, Belt Alignment | Woods Equipment L306 K50

Push Channel Attachment

Select desired cutting height (refer to Operation sec- tion), and attach push channel arms to idler bracket with 5/8 x 1-3/4 clevis pins (installed from outside in) and secure with safety pins.

Belt Installation

Pull belt to rear of tractor. Give belt a 3/4 clockwise twist between center pulley and left idler. Install belt under idler and route over drive pulley. A 1/4 clockwise twist should occur between right idler and center pulley. If any twist occurs other than these, the belt is incor- rectly installed. Recheck installation steps and correct as necessary.

Lift Chain Installation

Straighten lift chains so links are flat (without twist) and thread through front lift bracket chain idlers mounted directly above mower frame.

Route chain under tractor and through rear chain idlers mounted on idler bracket. Make sure chain remains flat. A twisted chain will not roll smoothly through chain idler. Insert end of chain into rear lift lugs mounted on tractor rockshaft arms. When cutting height is adjusted and installation complete, cut off excess chain leaving over 4".

Adjust cutting height (refer to Operation section, page 8).

Belt Alignment

Figure 19. Best Possible Alignment of Left Idler

Figure 20. Maximum Left Idler Should be Raised

Figure 21. Maximum Left Idler Should be Lowered

Figure 22. Best Possible Alignment of Right Idler

See Figure 19 through Figure 24. Belt alignment and tension should be set at the same time. It is suggested that you read both the Alignment and Tensioning sec- tions on page 23 before attempting either. Improper tension or alignment will affect belt life.

With mower level and cutting height set, check belt alignment.

Belt alignment is accomplished by adjusting idler pul- leys and/or moving the mower forward or to the rear with push channel adjustment.

Alignment tolerance are shown in Figure 19 through Figure 24. The best idler alignment is shown in Figure 19 and Figure 22. However, it is not always possible to achieve. Alignment may be set within the tolerances given but the left idler must always be at least 1" higher than the right.

Be sure belt does not rub on rear apron of mower. If mower is set to high cutting heights, it is sometimes necessary to run back of mower 1/4" lower than front to prevent this.

IMPORTANT

■Belt must not rub deck or crosswise support.

Figure 23. Maximum Right Idler Should be Raised

Figure 24. Maximum Right Idler Should be Lowered

Belt Tension

Set belt tension using a spring scale or other force measuring device. Remove right belt shield and attach scale between the center and right pulley. Apply between three and four pounds of force. Belt deflection should measure 5/16" for normal conditions.

Tension may be increased if necessary to prevent belt from slipping in heavy mowing conditions.

32695 (Rev. 11/17/2006)	Assembly 23

L306 K50 specifications

Woods Equipment L306 K50 is a robust and reliable tool designed specifically for agricultural and landscaping applications. This versatile equipment offers various features that enhance its performance, making it a valuable asset for farmers, landscapers, and contractors alike.

One of the standout features of the L306 K50 is its impressive cutting width. With a cutting width of 6 feet, this mower allows for efficient and quick mowing, significantly reducing the time it takes to maintain large areas. The high-quality blades ensure a clean and precise cut, contributing to a well-manicured appearance for lawns and fields.

The construction of the L306 K50 is another highlight. Made with heavy-duty, durable materials, it is engineered to withstand tough conditions and heavy use. The robust frame provides stability and strength, allowing it to tackle more challenging terrains without compromising performance. This durability means less downtime for repairs and more time spent on the job.

Advanced technologies integrated into the L306 K50 further increase its efficiency. The mower features a unique deck design that optimizes airflow, resulting in superior grass lift. This design helps to ensure an even cut and contributes to a healthier lawn by promoting proper grass growth. Additionally, the mower's adjustable cutting height allows users to customize their cutting experience according to the specific requirements of different grass types and terrain.

Operator comfort and control are prioritized in the L306 K50. The user-friendly controls are designed for ease of operation, allowing both seasoned professionals and novice users to handle the machinery effectively. Furthermore, the mower’s compact design enhances maneuverability, making it suitable for navigating tight spaces and obstacles commonly found in landscaped areas.

Maintenance is simplified with the Woods Equipment L306 K50. The mower is designed for easy access to key components, making routine inspections and maintenance tasks straightforward. This thoughtful design ensures that users can keep their equipment in optimal condition without the need for extensive tools or time.

Overall, the Woods Equipment L306 K50 stands out for its blend of power, versatility, and user-friendly design. With its high cutting performance, durable construction, and advanced features, it is an excellent choice for anyone looking to maintain expansive landscapes or agricultural areas with efficiency and ease. Whether for professional landscaping or personal use, the L306 K50 is designed to deliver outstanding results in a wide array of mowing tasks.