Assembly

Side Shield (See page 16)

Attach side shields (39 & 48) to mower with 3/8 x 1" bolts and lock nuts. A side discharge chute (48) may be installed on right end of mower in place of side shield (30).

Center Belt Shield Bracket & Pivot Pipe (See page 16)

Attach rear pivot pipe (17) and center belt shield bracket (10) to mower using 3/8 x 1-1/4 bolt, nut, and lock washer. Remove rear bolt from bracket (47). Secure center of pipe (17) and bracket (47) with 3/8 U- bolt (67), nut and lock washer.

Center Belt Shield (See page 16)

Attach center belt shield (9) to bolts welded in mower and belt shield bracket (10) using 3/8 nuts and lock washers.

Side Skids (See page 16)

Bolt skids in such a position that they will be carried close to the ground, but not ride continuously on the ground when mower is operated at desired mowing height. Use 3/8 x 1" heat treated bolts (torqued to 35 lbs-ft), lock washers, and nuts.

Front Toe Guards (See page 16)

Front toe guards (49) are furnished for some mowers. When provided, bolt them to front of mower using 3/8 NC x 3/4" carriage bolts and 3/8" flange lock nuts.

Idler Frame (See page 16)

Assemble idler sheaves to inside of adjustment slots as shown using 5/8 x 3-1/2 carriage bolts, flat washers, lock washers and nuts. Move tractor drawbar adjust- ment to bottom adjustment hole on the tractor.

Slide idler channel frame assembly (20) between the drawbar and the drawbar plate attachment bolts of the tractor. Attach with the clamp plates that are furnished using 1/2 x 2" bolts, lock washers and nuts.

Attachment Arms (See page 16)

Bolt attachment arms (18) to tractor with three 5/8 x 1-1/4 bolts and lock washers in each.

PTO Sheave (See page 16)

Remove paint from bore of sheave (32). Put 1" splined tapered bushing (31) in sheave (32), and insert screws to hold bushing in place, but do not tighten.

Mounting Mower (See page 16)

Slide mower under tractor. At this point, the belt must be looped over the pivot pipe. Screw guide rod (22) into rear of pipe (17). Do not tighten. Insert guide rod into second hole from bottom of idler bracket plate (for average mowing conditions).

Attach two adjustment arms (16) with single hole end to mower, other end to bottom of attachment arms using 5/8 x 1-1/2 clevis pins, washers, and safety pins. Place rear clevis pin in the most forward adjustment hole from rear of initial setting. This may need to be changed after belt is installed and lined up.

Belt Assembly and Adjustment

Position and pin push arms to the mounting brackets using 5/8 x 1-1/2 clevis pin and safety pins.

First put belt on the bottom groove, right hand side of the center sheave. Then thread it to the left, around the left hand sheave.

Figure 4.

Bring the belt back across the center sheave in the center groove over to the right outside sheave.

29927 (Rev. 3/14/2008)	Assembly 11

59C-2 specifications

The Woods Equipment 59C-2 is a robust and versatile implement that embodies the quality and durability associated with the Woods brand. Designed for compact tractors, this rotary cutter is a perfect solution for maintaining pastures, fields, and overgrown areas. It offers a combination of efficiency and performance, making it a favorite among agricultural operators and landowners alike.

One of the main features of the 59C-2 is its rugged construction. Built with a heavy-duty frame and premium materials, this cutter can withstand the rigors of daily use. Its 59-inch cutting width allows it to cover substantial areas quickly, increasing productivity. The cutter's design is also optimized for maneuverability, making it effective in tight spaces and around obstacles.

A standout characteristic of the Woods 59C-2 is its heavy-duty heat-treated blades. These blades are engineered to provide a clean and precise cut, ensuring that grass and brush are evenly trimmed. The blades are also replaceable, allowing users to maintain optimal cutting performance over time. This feature significantly reduces maintenance costs and extends the life of the cutter.

In terms of technology, the 59C-2 incorporates a slip clutch protection system. This system is essential for safeguarding the tractor and implement from potential damage caused by unexpected obstacles. When the blades encounter a tough object, the slip clutch disengages, preventing undue strain on the drivetrain and ensuring a longer lifespan for both the tractor and rotary cutter.

Another notable aspect of the Woods 59C-2 is its adjustable cutting height capability. Operators can easily set the desired height from 1.5 to 4 inches, allowing for flexibility in different mowing conditions and crop types. This adaptability is particularly beneficial for varying terrain and growth levels, providing a tailored approach to land management.

To facilitate easy attachment to a variety of compact tractors, the Woods 59C-2 features a universal mounting system. This design ensures a quick and straightforward setup, allowing operators to switch between implements seamlessly.

Overall, the Woods Equipment 59C-2 rotary cutter stands out for its durable construction, advanced technology, and versatile features, making it an excellent choice for anyone looking to maintain their property with efficiency and ease. Whether tackling tall grass or thicker brush, this implement demonstrates the quality performance that Woods Equipment is known for.

ASSEMBLY