Woods Equipment 59C-2 manual Lift Attachment See, Shielding, Casters

Page 12

Figure 5.

Then thread it back across the front of the center sheave in the top groove.

Figure 6.

Proper Twist: The belt then follows with a 3/4 twist back under the left V-idler, up over the drive sheave and back down under the right idler pulley. This will leave a 1/4 twist in the section of the belt extending from the right V-idler to lower groove of the center mower sheave.

Adjust the mower to proper cutting height. The front of the mower should be slightly lower than the rear for the best cutting and least power requirement.

Idler Adjustment: Make minor belt adjustment with idlers but keep left idler about 1" above being in line with the groove in which the belt runs on the center sheave of the mower and right idler about 1" below. Move mower fore and aft for major adjustments. On L306K210, K260, S & F10, use belt takeup idlers on mower deck for major adjustment.

After belts are properly aligned, lock sheave (32) and bushing (31) in place. Torque bolt to 12 lbs-ft alternat- ing back and forth at least six times.

NOTE: Make major belt adjustment by sliding mower fore and aft, using the five holes in arms as required. Make minor adjustments with idlers, but keep left V- idler about 1" above being in line with groove in which belt runs in center mower sheave and right V-idler about 1" below.

After mower is completely assembled and at the proper cutting height, tighten the center rear pivot pin securely.

Lift Attachment (See page 14)

Bolt lift assembly (14, 15, 83, and 85) to right hydraulic arm of tractor with two 5/8 x 1-3/4 bolts, nuts, and lock washers.

Attach one 33 link chain (11) through keyhole of each rear lift lug on mower frame. Install a plastic caplug (8) into keyhole below chain. Attach upper end of 33 link chain (11) to eye bolts (85). Raise mower slightly and adjust chains so mower will raise level and will not hit tires, etc., when fully raised.

Shielding

Bolt V-belt shield attachment bracket (26, page 16) to the tractor transmission housing with two 1/2 x 1" bolts and lock washers.

Place the V-belt shield (27, page 16) over the rear drive and secure with flat washers and wing nuts.

Casters

If casters are used, see page 18 through page 19 for parts drawings.

12 Assembly

29927 (Rev. 3/14/2008)

 

 

Image 12
Contents Rotary Mower Introduction To the DealerTable of Contents General InformationSafety Safety RulesTraining PreparationMaintenance TransportationStorage Safety & Instructional Decals Be CarefulTo Avoid Serious Injury or Death Operation OperationMowing Grass Tractor Operating InstructionsHOW to Solve Belt Problems Side Discharge & Discharge ChuteOptional Equipment Mower Spindle AssembliesHow to Align a Twisted Belt CleaningAssembly AssemblyLift Attachment See ShieldingCasters 2 Idler Bracket 2 Lift & Mounting Assembly Photo Dealer Check Lists Leaf Mulcher OptionalPRE-DELIVERY Check List Delivery CheckParts Part QTY Description 59 & L59 Casters L306 Casters 59 & L306 Leaf Mulcher Lift Chain Hook-Up Table Manual Height Adjustment Chain see chart for chain used on Spindle Assembly Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsWarranty Woods Equipment Company

59C-2 specifications

The Woods Equipment 59C-2 is a robust and versatile implement that embodies the quality and durability associated with the Woods brand. Designed for compact tractors, this rotary cutter is a perfect solution for maintaining pastures, fields, and overgrown areas. It offers a combination of efficiency and performance, making it a favorite among agricultural operators and landowners alike.

One of the main features of the 59C-2 is its rugged construction. Built with a heavy-duty frame and premium materials, this cutter can withstand the rigors of daily use. Its 59-inch cutting width allows it to cover substantial areas quickly, increasing productivity. The cutter's design is also optimized for maneuverability, making it effective in tight spaces and around obstacles.

A standout characteristic of the Woods 59C-2 is its heavy-duty heat-treated blades. These blades are engineered to provide a clean and precise cut, ensuring that grass and brush are evenly trimmed. The blades are also replaceable, allowing users to maintain optimal cutting performance over time. This feature significantly reduces maintenance costs and extends the life of the cutter.

In terms of technology, the 59C-2 incorporates a slip clutch protection system. This system is essential for safeguarding the tractor and implement from potential damage caused by unexpected obstacles. When the blades encounter a tough object, the slip clutch disengages, preventing undue strain on the drivetrain and ensuring a longer lifespan for both the tractor and rotary cutter.

Another notable aspect of the Woods 59C-2 is its adjustable cutting height capability. Operators can easily set the desired height from 1.5 to 4 inches, allowing for flexibility in different mowing conditions and crop types. This adaptability is particularly beneficial for varying terrain and growth levels, providing a tailored approach to land management.

To facilitate easy attachment to a variety of compact tractors, the Woods 59C-2 features a universal mounting system. This design ensures a quick and straightforward setup, allowing operators to switch between implements seamlessly.

Overall, the Woods Equipment 59C-2 rotary cutter stands out for its durable construction, advanced technology, and versatile features, making it an excellent choice for anyone looking to maintain their property with efficiency and ease. Whether tackling tall grass or thicker brush, this implement demonstrates the quality performance that Woods Equipment is known for.