Watkins MAL, LAP, SOR, TRI manual Splendors LED Lighting Optional, Filter Cycles, Clean Cycle

Page 17

La PalmaTM & Mallorca® Spas only:

1st press:

Two-speed jet pump runs on low speed

2nd press:

Two-speed jet pump runs on high speed

3rd press:

One and Two-speed jet pumps run on high speed

4th press:

One-speed jet pump runs on high speed

5th press:

Both jet pumps are off.

Sorrento® & Trinidad® Spas only:

1st press:

Two-speed jet pump runs on low speed

2nd press:

Two-speed jet pump runs on high speed

3rd press:

Jet pump off

READY

•During filter cycles or when the thermostat is calling for heat, the pump’s low speed operates automatically and cannot be turned off by pressing the Temp Up (▲) or Temp Down (▼) touch pad.

•The pump on high speed automatically turns off after operating for two hours. The pump on low speed automatically turns off after operating for two hours.

•When the jets are active, the JETS Icon on the control panel will illuminate.

LIGHT CONTROL

READY

Your Hot Spot® spa is equipped with a blue LED spa light. Press the LIGHT button to turn it on. The light automatically turns off after six hours. When the light is active, the LIGHT Icon on the control panel will illuminate. Press it a second time to turn the light to a medium light intensity, a third time for a low light intensity and a fourth time will turn it off. For enhanced spa enjoyment, an optional six color wheel light feature is available to create your desired ambience.

SPLENDORS ® LED LIGHTING (OPTIONAL)

The Splendors LED lighting system allows you to brighten up your spa experience through different multi-colored lights: red, blue, white, purple, amber, and aqua. You can choose one stationary color or you can cycle through all the colors with the automatic color wheel.

To install Splendors LED lights, you will need to contact your Hot Spot Dealer.

To activate, press the SET button followed by the LIGHT button. To select a specific color, push the LIGHT button (within 5 seconds) while the desired color is displayed. If 5 seconds have passed, after color wheel activation, you will need to press SET followed by the LIGHT button to select a specific color. The Splendors LED lighting option is a great way to personalize your spa experience.

FILTER CYCLES

SET

READY

F1

F2

When the spa is first powered up, the automatic filter cycle will wait 10 minutes before starting. Your spa will automatically turn the first filter cycle on for 60 minutes on low speed. The second filter cycle will activate for 30 minutes, 12 hours later. The filter cycle icon, F1 or F2 will be displayed in the control panel.

NOTE: The optional FreshWater® III ozone system only works during the filter cycle.

To modify the length of either filter cycle:

A.Press and hold the SET button for approximately three seconds.

B.Press the LIGHT button to select filter cycle 1 or 2 (F1 or F2 will be displayed).

C.Using the Temp Up (▲) or the Temp Down (▼) button, adjust the value as desired, from 0 to 6 hours.

D.After program is entered it will take10 seconds to save. Once saved, the display will then revert back to Temperature display.

 

The filter cycle will activate the jet pump on low speed for the entire cycle. When activated, the filter cycle Icon on the

READY

display is turned on. If the temperature exceeds the set point by three degrees F for more than three hours, the

F1

system will cancel the FILTER cycle and the filter Icon will blink for the remaining filter cycle time. Should the

 

temperature cool down to 1.5 degrees F below the set point before the end of the cycle, the cycle will resume for the

 

rest of the time. Should you use the spa during the filter cycle by placing the jet pump on high speed, the FILTER Icon

 

will blink. Once the jet pump has been shut off, a ten minute tranquil mode begins (FILTER Icon will be blinking during

tranquil mode) before the filter cycle will resume. The blinking filter Icon indicates that the filter cycle timer is still counting, but the cycle has been temporarily interrupted.

CLEAN CYCLE

The Clean Cycle has been provided as a convenient timer for water maintenance. When the Clean Cycle is initiated, the Jet pump will activate in high speed. The jet pump icons will flash on and off until the cleaning cycle is complete. The total cleaning cycle time is ten minutes. If the clean cycle does not engage, make sure the SPA LOCK is deactivated. To activate the Clean Cycle, press the SET button followed by the JETS button.

Page 14

Operating Instructions

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents N e r ’ s M a n u a l OwnerÕs Manual Table of Contents Important Safety Instructions Safety InformationAvoiding the Risk to Children DonõtUnclean water Health problems affected by spa useRisks to Avoid Avoiding the Risk of HyperthermiaSite Preparation Installation InstructionsImportant SPA Instructions Deck Installation Outdoor and Patio InstallationINDOOR/BASEMENT Installation Installation InstructionsSPA Cover Installation Electrical InstallationSelecting the Voltage for Your SPA Volt ConversionSorrento Trinidad Jumper Configuration Volt Subpanel Wiring InstructionsSpa Frog Spa Specifications & IllustrationLA Palmatm Model LAP 8 Spa Specifications & Illustration SPA Specifications & IllustrationMallorca Model MAL Overhead ViewSorrento Model SOR Trinidad Model TRI 10 Spa Specifications & IllustrationOperating Instructions START-UP and Refill ProceduresOperating Instructions Hydromassage Jets Heating and Hydromassage SystemsPrecision Jets AIR Control SystemSPA Control Panel Safety EquipmentSplendors LED Lighting Optional Clean CycleFilter Cycles La PalmaTM & Mallorca Spas onlyMusic Sound System Locking FeaturesStereo Control Panel Mode Button Jet Menu JET Pump 1 JET SystemJET Pump 2 JET System Directional Precision Jets on back left wall JET PumpDirectional Precision Jets on back right wall Directional Precision Jets in loungeJET System Sorrento Model SOR JET System MenuTrinidad Model TRI JET System Menu General Information Water Quality and MaintenanceMethods for Testing the SPA Water Water Quality and Maintenance HOT Spot SPA Water Maintenance ProgramFilling the SPA with Water Balancing the Total Alkalinity TABalancing the PH 22 Water Quality and MaintenanceMaintaining the Sanitizer Level Ideal pH level for your spa water isSPA Frog Water Care System SPA Frog Cartridge Replacement InstructionsIdeal Range ppm StepsFollowing the SPA Frog Sanitizer Routine 24 Water Quality and MaintenanceDoõs and Donõts Supplemental Water MaintenanceBromine Super ChlorinationFoam Inhibitors Cleaning the Ozone Injector26 Water Quality and Maintenance Common Water Chemistry Questions Question Why can’t I fill my spa with soft water?Filter Maintenance Maintenance and SPA Care28 Maintenance and Spa Care Water TerminologyCare of the SPA Pillows Maintenance and Spa CareLA Palma To remove and replace the spa pillowsCare of the SPA Cover Care of the ExteriorWood SPA Cabinet Simulated SPA CabinetNON-OPERATION in Cold Climate Winterizing Your SPAMiscellaneous Service Information Service InformationActs Invalidating Warranty Service InformationDisclaimers Watkins Customer ServiceProblem Probable causes Solutions TroubleshootingPage Watkins Manufacturing Corporation Vista, California USA

TRI, SOR, MAL, LAP specifications

Watkins MAL, LAP, SOR, and TRI represent a suite of advanced technology products designed for various applications across multiple industries. These systems are integral to enhancing efficiency, flexibility, and automation within operational workflows.

Watkins MAL, or Modular Automation Layer, serves as a flexible framework enabling the seamless integration of diverse automation systems. The architecture focuses on modularity, allowing users to customize their automation setup according to specific requirements. This feature significantly reduces installation time and costs while promoting scalability as businesses grow. The primary technology underpinning MAL is a robust communication protocol that ensures compatibility with various industrial devices, facilitating real-time data exchange and operational synchronization.

LAP, or Logistics Automation Platform, is tailored specifically for optimizing supply chain processes. It leverages advanced algorithms and machine learning to enhance inventory management, shipment tracking, and demand forecasting. LAP’s main characteristic is its intuitive user interface, providing users with comprehensive dashboards that present key performance indicators in real time. The integration of Internet of Things (IoT) technology allows it to connect with sensors and devices across the logistics network, optimizing various stages from warehousing to transportation.

SOR, which stands for Smart Operational Resilience, emphasizes risk management and sustainability in operations. This platform utilizes data analytics and predictive modeling to identify potential disruptions in the supply chain or production lines. It helps organizations develop contingency plans and build resilience against unforeseen challenges. The characteristic that sets SOR apart is its focus on sustainability, integrating eco-friendly practices and promoting resource conservation through its operational protocols.

Finally, TRI, or Technology Resource Integrator, is designed for comprehensive resource management across an organization. TRI enables businesses to consolidate various assets and technologies, ensuring optimal usage and performance. Its primary feature is a central management dashboard that provides insights into resource allocation, utilization rates, and operational efficiency. TRI integrates seamlessly with existing systems, utilizing APIs and standard protocols to ensure a cohesive technological ecosystem.

In conclusion, the Watkins suite encompassing MAL, LAP, SOR, and TRI provides businesses with innovative solutions to modern challenges. By focusing on automation, logistics optimization, operational resilience, and resource integration, Watkins enhances productivity and promotes sustainable growth in an increasingly competitive market.
Top Page Image Contents