White Rodgers 1050 Installation, Wiring & Operation, Installing the Outdoor Bulb

Page 2

INSTALLATION

Both the outdoor bulb and inside bulb should be installed before the control case, since capillary lengths of these bulbs will normally determine the final location for the control case.

NOTE

Use care not to bend or dent either of the sensing bulbs

ROOF

A. INSTALLING THE OUTDOOR BULB:

Locate the outdoor bulb so that it senses actual outdoor air temperature. Attach mounting bracket supplied with control to some convenient outside part of the building so that the outdoor bulb is:

1.Exposed to circulation of air and wind.

2.Shielded from rain, snow, and direct rays of sun.

3.Not close to false sources of heat such as dryer vents, exhaust fans, melting snow or ice, etc.

4.Sufficiently above ground to prevent tampering or being covered with snow, ice, or debris.

B. INSTALLING THE WATER BULB:

The water bulb should be installed in a hot section of the boiler. It should never be installed near a return inlet to the boiler.

C. INSTALLING THE CONTROL CASE:

The case of the Indoor-Outdoor Control should be installed as follows:

1.Install it on a vertical surface such as a wall or the side of a joist.

2.Do not install it on a heated surface such as on the boiler or a hot water pipe.

3.Install it high enough so that it will be convenient to make adjustments on round dial and large screw at bottom of case.

4.Install it so end of case with electrical outlet is on top.

CEILING

The underside of the eaves or overhang of a NORTH or NORTHWEST roof is normally a good location. It should be exposed to the circulation of air and wind.

INSTALLED

ON JOIST

INSTALLED

HIGH ON WALL

MOUNTING

BRACKET

OUTDOOR BULB

WIRING & OPERATION

All wiring should be done in accordance with local and national electrical codes and ordinances.

This indoor-outdoor control is designed to vary boiler temperature according to outdoor weather conditions. For this reason, it is recommended that this control only be used on systems where the domestic hot water supply is heated by a separate source from the heating boiler. The most common method for using an indoor-outdoor control is shown in the block diagram below, and in the wiring diagrams which follow. A separate high limit control should always be used with an indoor-outdoor control.

INDOOR

OUTDOOR

CONTROL

HOT WATER BOILER

HIGH LIMIT

CONTROL

ROOM THERMOSTAT

RELAY

BURNER

CIRCULATOR

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Specifications Installation InstructionsPrecautions Operator Save these instructions for future useInstalling the Outdoor Bulb InstallationWiring & Operation Installing the Water BulbUsing Oil burner control Using diaphragm Gas ValveUsing Gas or Burner OperationSetting the Square Dial Dial SettingsSetting the Round Dial Additional AdjustmentsChart 3 Round Dial Set 4 divisions Warmer than N Chart 2 Round Dial Set 2 divisions Cooler than NChart 1 Round Dial Set at N Additional InformationDescription Précautions Instructions D’INSTALLATIONRégulateur D’EAU Chaude INTÉRIEUR-EXTÉRIEUR SpécificationsInstallation DU Boitier DE Commande Installation DU Capteur ExtérieurInstallation DU Capteur Intérieur Câblage ET UtilisationCâblage ET Mode D’EMPLOI suite Réglage DU Cadran Carré Réglage DES Points DE ConsigneRéglage DU Cardran Rond AjustementsGraphique 1 Cadran rond réglé à N Réglage DES Points DE Consigne suiteRenseignements Supplémentaires

1050 specifications

The White Rodgers 1050 is a programmable thermostat designed to optimize energy savings while providing exceptional comfort for homeowners. With its user-friendly interface and advanced features, it has become a popular choice in modern HVAC systems.

One of the standout features of the White Rodgers 1050 is its programmable capability, allowing users to schedule temperature adjustments based on their daily routine. This feature helps maintain an ideal environment while reducing energy consumption. The unit typically offers four programmable periods per day, giving users the flexibility to customize settings for different times, whether it's day, evening, or overnight.

Additionally, the White Rodgers 1050 is equipped with a large, clear display that is easy to read, even from a distance. This backlit screen enhances visibility, particularly in low-light conditions, making adjustments a breeze. The intuitive layout of the buttons simplifies navigation through the various settings, enabling users to change temperatures or modes with minimal effort.

The thermostat utilizes advanced technology to enhance its performance. One of its key features is the adaptive recovery mode, which learns how long it takes to heat or cool a space to the desired temperature. This ensures that the home reaches the preferred temperature at the scheduled time without wasting energy. Moreover, the 1050 includes an automatic changeover feature, allowing it to switch seamlessly between heating and cooling modes based on the home’s needs, thus providing year-round comfort.

Another significant characteristic of the White Rodgers 1050 is its compatibility with a wide range of heating and cooling systems, including gas, electric, heat pump, and multi-stage systems. This versatility makes it a suitable option for various HVAC setups.

For those concerned about energy usage, the White Rodgers 1050 provides energy usage reports and alerts, helping homeowners monitor their energy consumption patterns. This feedback can motivate more energy-efficient practices, ultimately leading to lower utility bills.

In conclusion, the White Rodgers 1050 thermostat blends advanced technology, user-friendly features, and energy-saving capabilities into a single, efficient device. Its programmable options, adaptive recovery feature, and compatibility with various systems make it a valuable addition to any home looking to optimize comfort and efficiency. Whether you are upgrading an existing system or installing a new one, the White Rodgers 1050 is poised to deliver the performance and convenience modern homeowners expect.
Top Page Image Contents