Swisher E4-S3000 manual Troubleshooting Guide, Remedy, Symptom, Possible Cause

Page 17

Troubleshooting Guide (continued)

Symptom

Poor acceleration.

Engine stops abruptly.

[Engine difficult to shut off._

Possible Cause

Clogged air filter,

Clogged fuel filter,

Lean fuel/air mixture.

Idle speed set too low.

Switch turned off.

Fuel tank empty,

Clogged fuel filter,

Water in the fuel,

Shorted spark plug or loose terminal,

Ignition failure.

Piston seizure.

Ground (stop) wire is disconnected or switch is defective.

Overheating due to incorrect spark plug.

Remedy

Clean tile air filter.

Replace tile fuel filter.

Consult with an authorized servicing dealer.

Adjust: 3,000 (±300) RPM (mind).

Reset tile switch and restart.

Refuel. See page 10.

Replace fuel filter.

[)rain; replace with clean fuel. See page 10.

Clean and replace spark plug, tighten tile terminal.

Replace tile ignition unit.

Consult with an authorized servicing dealer.

Test and replace as required.

Idle engine until cool.

Clean and regap tile plug to 0.024- 0.028

inch (0.6- 0.7 ram). Correct plug: NGK CMR5H or equivalent resistor type spark plug of tile

correct range.

 

 

 

Overheated engine.

dirtyTop ofandengineoily. is getting

_

Valve cover is leaking.

Cutting

attachment

 

 

 

rotates

at engine idle.

 

Broken clutch spring or worn clutch

 

 

 

 

 

_

spring

boss.

 

 

Engine

idle too high.

Loose attachment holder.

[ Engine will not idle down. ]-----,,+ Engine idle set t°° higlL

Engine has an air leak.

Idle engine until cool.

Consult with an authorized servicing dealer.

Set idle: 3,000 (±300) RPM (rain-l).

Replace spring/shoes as required, check idle speed.

Inspect and re-tighten holders securely.

Set idle: 3,000 (±300) RPM (rain-l).

Consult with an authorized servicing dealer.

Symptom

I Excessive vibration.

Cutting attachment will not rotate.

Possible Cause

Warped or damaged cutting attachment.

Loose gearcase.

Bent main shaft/worn or damaged bushings.

Trhnmer line not wound properly on spool.

Shaft not installed in powerhead or

gearcase.

Broken shaft.

Damaged gearcase.

Remedy

Inspect and replace attachment as required.

Tighten gearcase securely.

Inspect and replace as necessary.

Rewind trhnmer line.

17

Image 17
Contents E4--$3000 Frmmer Introduction ContentsProperly Equipped Operator General Safety InstructionsStay Alert Use Good JudgmentEnvironment Safety LabesBe Aware of the Working Prior to Assembly Specifications E4-$3000Assembly and Adjustments Assemby and AdjustmentsAdjust Throttle Lever Free Play E4-$3000 HandleE4-$3000 Install the Cutting Attachment ShieldFilling the Fuel Tank Install the Trimmer HeadMixing Fuel Arnng When the Engine StartsStarting the Engine Stopping the Engine Die Speed AdjustmentCutting GrassmUnits equipped with a trimmer head Shoulder StrapEngine Operating Speeds EdgingMaintenance General MaintenanceHourMaintenance DailyEvery 10 to 15 hours of operation 10/15-Hour MaintenanceHour Maintenance Valve Adjustment 139/150-Hour MaintenanceSpark Attester Screen Maintenance Long Term Storage Speed-Feeff 375 LoadingInstructions PIN78890-28000YES Jr Possible Cause Troubeshootin GuideSymptom Troubleshooting GuideRemedy Possible CausePage Page What is Covered by this Warranty Manufacturers Warranty CoverageWhat is Not Covered This Warranty is Administered by