How to Stop and Park the Mower

Come to a complete stop. If the blades are on, turn them off using the switch on the instrument panel. Make sure the control levers are in the exact neutral position. Set the parking brake, reduce the engine speed to idle, shut off the ignition switch to stop the engine and then remove the key from the ignition switch. The mower is now parked. Do not leave mower unattended on a sloped surface.

How to Drive the Mower Over a Curb

To climb a curb, first see the Safety Instruction Manual section of this manual, especially the parts on:

•Initial Operating Safety Guidelines •Operation In Reverse •Operation In Forward Direction

Next, raise the mower deck into the locked transport position. This is the highest position for the mower deck. Then drive the mower in reverse at a 45 degree angle to the curb (with the left side of the mower closest to the curb) until you are within an inch or two of the left-rear tire hitting the curb. Stop and then gradually bump into the curb with that tire until it is just on top of the curb. If the tire slips even while lurching the mower into the curb, then the curb is too high and you should use ramps or find another way. The mower should still be at a 45 degree angle to the curb. Now, while maintaining the same angle to the curb, continue to back up until the right- rear tire is close to the curb. Using the same technique lurch the right tire onto the curb. After both wheels are on top of the curb, turn the mower counterclockwise and back up so the left caster wheel comes over and last should be the right caster wheel as the mower is twisting to the left (counterclockwise). The technique works the best if you try not to drive backwards at a near 90 degree angle to the curb but get all of the wheels to go over while the mower is moving at least a 45 degree angle to the curb. To drive off a curb, first try driving up onto it to make sure the curb is not too high. If the curb is not too high, drive the right-front caster off first while driving toward the curb at a 45 degree angle (the curb should be to your right). Then, maintain that 45 degree angle so the left caster goes over, then the right-rear wheel, then the left rear wheel.

WARNING

Never drive straight onto or off a curb.

Never drive straight onto or off a curb. If you do the whole procedure at a very sharp angle it will tend to minimize the contact of the mower deck with the

curb and you will be able to more safely control the mower.

How to Use the Mower on Varying Terrain

See the Safety Instruction Manual section of this manual, especially the parts on:

•Initial Operating Safety Guidelines •Operation On Slopes •Operation In Reverse •Operation In Forward Direction •Operation During Zero-Radius Turns

How to Adjust Neutral

Neutral refers to the mower movement when the engine is set to full throttle, parking brake is off, and the control levers are in the neutral position. The mower should not move forward or backward during this time. If the mower is moving forward or rearward, the neutral setting must be adjusted. The hydraulic pump has a Return-to-Neutral (RTN) device built into the linkage of the pump. To make the adjustment, loosen the ¼” allen bolt and rotate the RTN device until the neutral position is found and then retighten the ¼” allen bolt. Use care not to over tighten the allen bolt.

How to Change the Speed/Sensitivity

Adjustment

The WZK has three Speed/Sensitivity settings. The settings are changed by removing the control rod at the control levers and inserting into the alternate holes.

	Factory Setting
Slow Hole		12 MPH
10 MPH
10 MPH


		Fast Hole
		13.5 MPH

The controls are initially set with the Speed/ Sensitivity adjustment in the 12 MPH position. With operators not completely familiar with the mower operation the operator may desire to leave the controls in the factory setting or move to the slow hole position until becoming familiar with the operation. The faster setting has a corresponding increase in the sensitivity of the controls. In other words, a given amount of movement of the control levers will cause about a 10-15% increase in the ground speed making the controls more sensitive. After stopping the engine, the adjustment is made by removing rod ends connected to the control rods from the current holes in the control levers and reinstalling them into the alternate holes. The holes closest to the operators position are for the faster, more sensitive setting and the holes farthest from the operators position

4213, 4214, 4211, 4212, 4216 specifications

Wright Manufacturing is renowned for its commitment to producing top-tier commercial mowers, and the Wright Manufacturing 4219, 4214, 4212, 4216, and 4215 models exemplify this excellence. These mowers are designed for professionals who require robust, efficient, and dependable performance.

The 4219 model is distinguished by its powerful engine options and a cutting width that offers high productivity. This mower features a unique weight distribution system, ensuring stability and maneuverability even on hilly terrains. Its cutting system is engineered to provide a clean cut, promoting healthy grass growth, and its heavy-duty construction ensures long-lasting durability.

Moving on to the 4214 model, this mower is geared towards those who seek a balance between performance and compactness. With a slightly smaller frame, the 4214 is perfect for navigating tighter spaces without sacrificing power. The mower utilizes advanced technology, including a patented belt drive system that enhances efficiency while reducing maintenance costs. Its ergonomic design allows operators to work longer with reduced fatigue.

The 4212 model stands out for its simplicity and ease of use. It is ideal for smaller commercial operations or residential users needing professional-quality performance. The mower is equipped with intuitive controls, making it accessible to operators of all skill levels. Despite its smaller size, the 4212 does not compromise on cutting quality, delivering an exceptional finish on any lawn.

The 4216 combines innovation with robust engineering, featuring a wider cutting deck that optimizes productivity. It is built with fuel efficiency in mind, which helps reduce operational costs for commercial users. Additionally, the mower's durable chassis ensures stability during operation, and its advanced anti-scalping features guarantee a superior cut even on uneven surfaces.

Lastly, the 4215 model is engineered for versatility and adaptability. It integrates cutting-edge technology with user-friendly controls, making it suitable for various mowing conditions. One of its notable features is the customizable height adjustment system, allowing operators to achieve the perfect cut for different grass types and terrains.

Overall, Wright Manufacturing's 4219, 4214, 4212, 4216, and 4215 models offer a blend of power, efficiency, and versatility. Each model is tailored to meet the diverse needs of professionals in the landscaping and lawn care industries, showcasing Wright Manufacturing's dedication to quality and innovation in lawn maintenance solutions.