Wright Manufacturing 14SH654 owner manual Inspect Mower Before Each Use, How to start the mower

Page 11

OPERATING INSTRUCTIONS

WARNING

If you are not completely familiar with the Safety Instruction Manual read it now before proceeding with the operation of the mower. REMEMBER THERE ARE CERTAIN PRECAUTIONS LISTED IN THIS MANUAL THAT YOU MUST NOW TAKE BEFORE STARTING THE MOWER.

Inspect Mower Before Each Use

Inspection of Mower: Do not use the mower if any parts are not maintained in good operating condition. Examine all moving parts prior to each use. Look for excessive wear, bald drive tires or worn out front tires (normally smooth), cracks in parts, loose or missing bolts, cotter, linchpin or “hair” pins or cable yoke pins and replace before operating the mower. Make sure all safety equipment provided with the mower is in good operating order, including all warning decals and the operator-presence device which stops the engine and blades when the foot-operated Operator Presence Control (OPC) switch is released. To test the OPC, follow the instructions given later in this manual. Inspect the two anti-tip rollers and their respective bolts at the rear of the mower for tightness and proper operation. Ensure that all parts of the Quick-Cut Height control system are tight and secure. This is to reduce the possibility that the mower could have a loss of control or safety.

Basic Operation: The following procedures are to guide you through the basic operation of the mower. You should be a qualified mower operator according to the safety section of this manual. If this is your first time, operation should only be done with the assistance of your dealer on a level area. You should go through each step, in the order indicated, every time you start the mower.

WARNING

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.

How to start the mower

Before starting the engine

•Move mower to an open, well ventilated area.

•Make sure the control levers are in the exact neutral position.

•Apply the parking brake if it is not already set.

•Turn OFF the blade engaging switch if it is on.

•Check the engine oil.

•Turn fuel valve to the “ON” position.

Starting the engine

•Start the engine according to the engine manufacturer’s recommendation, see engine manual. Set the throttle control lever near mid throttle, pull out on the choke control knob and turn the key to the start position. Do not engage the starter for more than ten (10) seconds at a time. This may overheat the starter and the wiring systems. Wait ten (10) seconds between attempts. If the engine does not start after several attempts or stalls frequently, take the mower in for service.

After starting the engine according to the engine manufacturer’s recommendation, push in on the choke control knob to open the choke valve, let the engine run for several minutes to get the hydraulic fluid circulating through the pumps, etc. and to allow the engine to warm up. Do not over-rev a cold engine.

Unusual noises or irregular operation:

As you drive the mower, listen for any unusual noises and test for irregular operation and adjust or service as necessary.

How to drive the mower

While sitting or standing, both feet should be firmly placed on the foot platform. Set the engine speed about a fourth of the way from idle. Release the parking brake. Now try moving the hand control levers, one at a time, very slightly, forward and backward. Check to see if the wheels move forward and backward according to the position of the levers. If not, check to see that the pump release valves are closed. With both feet still firmly placed on the foot platform, increase the engine speed to about half of the way from idle speed. Release the parking brake. The higher engine speed will make the controls much more responsive and the mower much quicker;

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Revised 7/2011 Safety Alert Table of Contents PRE-DELIVERY Service of Mower by Dealer Mower is now ready for delivery to your customer User Qualifications General Safety InstructionsIntroduction Owner/User NoticeWork Area Conditions & Inspection Regular Mower Safety MaintenanceUser Clothing Inspect Mower Before Each UseOperation In Reverse Initial Operating Safety GuidelinesOperation In Forward Direction Operation on Slopes Fuel SafetyZero-Radius Turn Operation Replacement Parts Hydraulic SafetyStarting the engine How to start the mowerHow to drive the mower Inspect Mower Before Each UseMowing on Varying Terrain How to Stop and Park the MowerHow to Adjust Neutral Driving the Mower Over a CurbHow to Test/Use the Blade Clutch/Brake Switch Changing the Speed/Sensitivity AdjustmentHow to Perform the Tracking Adjustment Service and Adjustments How to Test the Operator Presence Control OPC SwitchReplacing Drive Belt Deck Lift Assist AdjustmentReplacing the Cutter Deck Belt Lubrication Seat AdjustmentsHow to Move the Mower if the Engine Won’t Start Bleeding Air from the Hydraulic System Battery ServiceSpindle Set Up / Blade Options Torque SpecificationsBLADE, Mulching Sport X Consumables / Maintenance Items Maintenance Interval Chart Maintenance Record Decals Wright MANUFACTURING, INC. Power Equipment Limited Warranty Mowing Tips Recommended Mowing HeightsMANUFACTURER’S Warranty Coverage Warranted Parts 4600X Wedgewood Blvd Frederick, MD

14SH654 specifications

Wright Manufacturing is renowned for producing high-quality lawn care equipment, and among its impressive range of products is the Wright Manufacturing 14SH654 mower. This mower is specifically designed for efficiency, durability, and ease of use, making it an ideal choice for both residential and commercial landscaping needs.

One of the standout features of the 14SH654 is its powerful engine. It is equipped with a fuel-efficient engine that provides ample power for tackling even the toughest mowing tasks. This engine is designed to deliver consistent performance, ensuring that users can complete their mowing jobs quickly and effectively.

The mower’s cutting deck is another remarkable characteristic. The 14SH654 features a durable steel cutting deck that ensures a precise cut every time. The deck size is optimized for maneuverability without sacrificing cutting width, allowing users to navigate intricate landscapes and tight spaces with ease. Additionally, the deck's design promotes superior airflow, resulting in cleaner cuts and better grass clipping dispersal.

Wright Manufacturing's commitment to user comfort is reflected in the design of the 14SH654. The mower comes with an ergonomically designed handle that reduces vibration, making it more comfortable for extended use. The adjustable handle height accommodates users of various heights, ensuring an ergonomic mowing experience every time.

Technologically, the 14SH654 includes features that enhance its usability. For instance, the mower is equipped with a reliable starting system, minimizing start-up frustrations. The robust wheel system enables smooth navigation across various terrain types, from flat lawns to hilly landscapes. Its reliable traction helps prevent slippage, providing stability while mowing.

Moreover, the 14SH654 has a built-in mulching system, which allows for efficient grass management. This feature returns finely shredded grass clippings back onto the lawn, acting as a natural fertilizer that promotes healthier grass growth. Users can also choose to bag the clippings for a tidy finish, highlighting the mower's versatility.

In summary, the Wright Manufacturing 14SH654 mower stands out due to its powerful engine, durable cutting deck, user-friendly design, and advanced technological features. It encapsulates the essence of high-performance mowing equipment, designed to meet the diverse needs of users while delivering superior results. Whether for home maintenance or professional landscaping, the 14SH654 is a reliable choice for anyone looking to enhance their mowing experience.
Top Page Image Contents