Yazoo/Kees ZKH61252, ZKH52252 Adjustments Mule Drive Belt Tension, Throttle Lever Tension

Page 8

ADJUSTMENTS

Figure 3

MULE DRIVE BELT TENSION:

1.Stop engine and remove the key.

2.Check to make sure the bolt head in the spring loaded idler pulley, on the left side of the engine deck is positioned between the two alignment holes in the left support plate

(See Fig 4).

3.If adjustment is necessary, loosen the adjustable idler pulley on the right hand side of the engine deck so it can move up and down in the slot. Place a wrench on the 3/8" nut in the center of the spring loaded idler pulley and rotate the idler upward to relieve the tension on the belt. Reposition the right side pulley in the slot and tighten. Recheck alignment of the bolt on the spring loaded idler.

Figure 4

THROTTLE LEVER TENSION:

1.Stop engine and remove key.

2.If throttle lever becomes loose, tension may be adjusted by tightening the pivot bolt. The pivot bolt holds the throttle arm to the throttle mounting bracket which is located under the console. Access is gained by removing the foot plate and the kick plate. See page 3.

REVERSE SPRING DETENT ADJUSTMENT:

1.Stop engine and remove key.

2.Rotate seat latches out to release seat. Located at the bottom rear of seat. Put seat in rear slide position, tilt seat forward, remove seat stop rod bolt and nut, tilt seat forward to rest on front frame.

3.Start with either the right or left motion control lever. Move the motion control lever to the neutral position then pull the lever back until the clevis pin (on the arm below the pivot shaft) comes into contact with the end of the slot. At this point slight spring pressure should be felt ( See Fig 5a).

4.Check where motion control lever is relative to the neutral slot in the console. The lever should be centered to allow it to pivot outward into the neutral slot.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operator’s Manual for Accordance with Instructions and Common SensePage Table of Contents Safety Setup and AdjustmentsMaintenance Specifications Trouble ShootingOperation Safety TrainingPreparation Transportation Equipment Setup and Adjustments Mower Deck Leveling Adjustments Park BrakeCutting Height Throttle Lever Tension Adjustments Mule Drive Belt TensionReverse Spring Detent Adjustment Adjustments Adjustments Motion Control Linkage Adjustment Operating Instructions ControlsOperating Instructions Starting and Operation Maintenance Maintenance Specifications Peak TorqueProblem Possible Causes Wiring Diagram Service Record Page

ZKH61252, ZKH52222, ZKH52252 specifications

The Yazoo/Kees ZKH61252, ZKH52222, and ZKH52252 are advanced, high-performance machines designed for landscaping, grass care, and other turf management tasks. These models embody the combination of durability, efficiency, and user-friendliness that the Yazoo/Kees brand is renowned for.

One of the standout features across these models is their powerful engines, which provide reliable performance and robust torque. Powered by industry-leading engines, the ZKH series ensures that operators can tackle even the most challenging terrains with ease. The ZKH61252, with its higher horsepower, is particularly suited for large commercial properties and demanding landscaping projects, while the ZKH52222 and ZKH52252 are perfect for residential lawns and smaller tasks without sacrificing power or efficiency.

The innovative cutting deck design is another hallmark of the ZKH series. These mowers feature advanced mulching technology, which finely chops grass clippings and redistributes them evenly back onto the lawn. This not only enhances the aesthetics of the lawn but also supports healthy growth by returning nutrients to the soil. The cutting height adjustment system is precise and user-friendly, allowing operators to achieve the perfect cut for various grass types and conditions.

Ergonomics and operator comfort have not been overlooked in the ZKH series. The models feature plush, contoured seats that reduce fatigue during extended mowing sessions. The intuitive control layout ensures that operators can easily fine-tune settings without having to divert their attention from the task at hand. Additionally, the ZKH series incorporates vibration-dampening technology, which further enhances ride comfort, making it easier for operators to navigate rough terrains.

In terms of technology, the ZKH61252, ZKH52222, and ZKH52252 integrate advanced features such as zero-turn capabilities, allowing for exceptional maneuverability around obstacles, flower beds, or trees. This increases productivity and reduces mowing time, making these machines invaluable for both professional landscapers and homeowners.

Durability is also a key characteristic of the Yazoo/Kees ZKH series. With a robust frame construction and high-quality materials, these mowers are built to withstand the rigors of regular use. The maintenance-friendly design ensures that routine servicing can be accomplished quickly and easily, maximizing uptime.

In summary, the Yazoo/Kees ZKH61252, ZKH52222, and ZKH52252 represent a blend of power, efficiency, comfort, and advanced technology. Suitable for both commercial and residential applications, these machines deliver exceptional performance and a premium mowing experience, making them an excellent choice for any landscaping enthusiast.
Top Page Image Contents