Yard-Man 24A-060F401 manual Operating Your Yard Vacuum, Stopping Engine, Gas And Oil Fill-Up

Page 8

Chipper Chute

Allow twigs and small branches up to 1 1/2” in diameter to be fed into the impeller for chipping.

Blower Chute (If Equipped)

When attached to unit the blower chute is used to blow or scatter yard waste such as leaves, pine needles, or small twigs across yard.

Nozzle Height Adjustment Lever

Used to adjust the nozzle ground clearance ranging approximately 5/8” to 4 1/8”.

Nozzle

Yard waste such as leaves or pine needles can be vacuumed up through the nozzle for shredding.

Hose Handle

Used to guide hose assembly when vacuuming.

Nozzle/Hose Vac Handle

The nozzle/hose vac handle is located on top of the nozzle and it is used to regulate the vacuum between the nozzle and the hose assembly.

Throttle Control Lever (Not Shown)

The throttle control lever is located on the engine. It controls the engine’s speed and stops the engine. See separate engine manual packed with unit for details.

Engine Controls

See the separate engine manual for the location and function of the controls on the engine.

Hose Assembly

Used as an alternative to the nozzle to vacuum yard waste such as leaves or pine needles in hard to reach places.

Stopping Engine

•Move throttle control lever to STOP or OFF position.

•Disconnect spark plug wire from spark plug and ground against the engine.

SECTION 4: OPERATING YOUR YARD VACUUM

WARNING: The operation of the Yard Vacuum can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses provided with this unit or eye shields before chipping or blowing and while performing any adjustments or repairs.

Gas And Oil Fill-Up

Service the engine with gasoline and oil as instructed in the separate engine manual packed with your Yard Vacuum. Read instructions carefully.

WARNING: Never fill fuel tank indoors with engine running or until the engine has been allowed to cool for at least two minutes after running.

Starting Engine

•Attach spark plug wire to spark plug. Make certain the metal cap on the end of the spark plug is fastened securely over the metal tip on the spark plug.

•Make sure safety switch wire is connected to engine and properly grounded.

•Engines with choke lever:

Move choke lever on engine to CHOKE position. (A warm engine may not require choking).

•Engines with primer:

Prime engine as instructed in separate engine manual.

•The throttle control is located on the engine. Move engine throttle control lever to FAST or ON position.

•Stand behind unit, grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point).

•Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly.

•Repeat previous steps until engine fires. When engine starts, move choke control (if equipped) gradually to RUN position.

WARNING: Never run the engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

To Empty Bag

•Unhook bag straps from the lower handle and unsnap bag clip from the top of lower handle. See Figure 7.

•Grasp bag handle with one hand and pull lock rod on mounting bracket with other hand toward engine to release.

•Remove bag from rim of the discharge opening. Refer to Figure 4.

•Twist the two buttons on the back of the bag to unlock and empty contents. See Figure 7.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OPERATOR’S Manual Table of Contents Finding Model NumberEngine Information Calling Customer SupportPreparation Important Safe Operation PracticesTraining Maintenance and Storage OperationDisconnecting Spark Plug Wire Assembling Your Yard VacuumRemoving Unit From Carton Loose Parts In Carton See FigureAttaching The Bag Attaching The Hose AssemblyAttaching The Handle Know Your Yard Vacuum Starter HandleBag Bag HandleOperating Your Yard Vacuum Stopping EngineGas And Oil Fill-Up Starting EngineTo Remove Blower Chute Using the Nozzle VacuumUsing the Hose Assembly Lubrication Nozzle Height AdjustmentCustomer Responsibilities Engine MaintenanceRemoving The Flail Screen Storing Your Yard Vacuum Troubleshooting Problem Cause RemedyModel 24A-060F401 Part Description Model 24A-060F401 Impeller Assembly 781-0735 Pin Clip 719-0329 Page Servicio Telefónico DE Asistencia AL Cliente ÍndiceBúsqueda DEL Número DE Modelo Preparación Sección 1 Medidas Importantes DE SeguridadCapacitación Funcionamiento Mantenimiento Y AlmacenamientoSección 2 Montaje DE LA Aspiradora Para Patios Extracción de la unidad de la cajaPiezas sueltas en la caja Ver Figura Desconexión del cable de la bujíaMontaje de la manija Colocación de la bolsaManija de la bolsa Manija del arrancadorBolsa Detención del motor Carga de gas y aceiteEncendido del motor Descarga de la bolsaUso del montaje de la manguera Extracción del canal de sopladoUso del pico de la aspiradora Ajuste de la altura del pico Responsabilidades del clienteLubricación MantenimientoAfilado o recambio de las hojas de la cortadora Patios Sección 6 Guía Para LA Solución DE Problemas Problema Causa SoluciónGarantía Limitada DEL Fabricante Para MANUFACTURER’S Limited Warranty for

24A-060F401 specifications

The Yard-Man 24A-060F401 is a robust and versatile lawn tractor designed to deliver exceptional performance for homeowners looking to maintain their lawns with ease. One of the standout features of this model is its powerful engine. Equipped with a reliable and efficient Briggs & Stratton engine, the Yard-Man 24A-060F401 provides ample power to tackle even the toughest mowing tasks. The engine design emphasizes reliability while also ensuring optimal fuel consumption, making it an excellent choice for eco-conscious consumers.

With a cutting deck measuring 42 inches, this lawn tractor offers a wide cutting path that reduces mowing time significantly compared to smaller models. The steel deck construction enhances durability and ensures that it withstands the rigors of regular use. Users can choose from multiple cutting heights, with an easy-to-use lever for adjustment, enabling precision mowing for different grass types and conditions.

Another important characteristic of the Yard-Man 24A-060F401 is its hydrostatic transmission system, which allows for smooth and effortless speed control. This feature is particularly advantageous for maneuvering around obstacles such as trees and garden beds, giving the operator complete control over the mowing experience. The tractor is designed to provide a comfortable ride, featuring an adjustable seat that accommodates users of varying heights.

The Yard-Man 24A-060F401 also integrates advanced technologies to enhance user experience. For instance, its ergonomic steering wheel makes navigation simple, while the integrated cup holder adds convenience for longer mowing sessions. The tractor is designed with easy access to essential controls, promoting a user-friendly interface that both novices and experienced users can appreciate.

For added versatility, the Yard-Man 24A-060F401 is compatible with various attachments, including mulch kits and baggers, which can further enhance mowing efficiency and lawn care options. The tractor's sturdy construction and premium features make it a solid investment for anyone looking to achieve pristine lawn aesthetics with minimal effort. In summary, the Yard-Man 24A-060F401 stands out for its power, user-friendly design, and adaptability, delivering reliability and performance that homeowners can trust.
Top Page Image Contents