Yard-Man 13B-325-401 manual Using The Mower

Page 12

Pivot the hood assembly up. Pull up the

 

grasscatcher bag by the handle and take it to the

 

 

proper disposal site. See Figure 10 .

 

Hold the bag away from your body. Push down

 

on the bag lever and let the bottom section of

 

 

the bag fall downwards. The grass clippings

 

 

will be disposed of from the bottom. See

 

Figure 10 .

 

Tap the bag on the ground so that the three legs

 

of the bag press against the ground. The bag

 

 

lever should snap close while you push the bag

 

 

downwards.

Replace the bag on to the mower making sure the bag is placed on the flange on top of the discharge chute. Pivot the hood assembly down.

When mowing an area for the first time, watch out for objects lying on the grass. If you strike a foreign object, stop the engine. Remove wire from spark plug and thoroughly inspect the mower for any damage. Repair the damage before operating it again.

Avoid scalping the lawn by adjusting the cutting height upwards and/or sharpening the blades. Mow at full throttle. Learn the terrain on which you are mowing. For best mowing results, mow only when the grass is dry.

The recommended mowing pattern is given below:

Grass Catcher Bag

Bag Handle

 

 

Push

 

here

Hood

Assembly

Mow grass often and in regular intervals so that you can cut only 1/3 of the grass blade in one mowing. To empty grass bag, stop the mower completely, engage the parking brake, and turn the ignition off. This will prevent the hot engine exhaust gas from browning the grass.

Many communities no longer haul grass clippings to landfills. Composting the clippings from your grass catcher is a viable solution. For this you will have to empty the grass catcher at the designated composting site.

Figure 10

Using The Mower

Your rider mower is equipped with a mulching plug to mulch the grass and recycle into the lawn instead of collecting in the grasscatcher bag.

Observe safety rules listed on pages 3-5 of this manual

for safe operation of your mower.

 

Before mowing, make sure that the cutting deck is leveled. For deck adjustment, refer to page 14.

• You can engage the blade by pressing on the blade

engagement pedal with your left foot while sitting

 

on the operator’s seat.

 

Mulch only when the grass is dry. Mulching wet grass may damage the underside of the deck because wet grass tends to stick to it. Clean deck thoroughly if you mulch wet grass.

For effective mulching, overlap mowing paths so that the clippings are distributed evenly.

12

Image 12
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General OperationSlope Operation Do Not Tires and other harmful waste Slope Guage Attaching Battery Cables Unpacking & Assembling Your Rider MowerLoose Parts Attaching Side-Discharge ChuteAttaching Mulch Plug Attaching Bumper OptionalAttaching Hitch Plate Optional Know Your Rider Mower Safety Interlock Using Shift LeverGrass Fill Level Indicator Stopping MowerOperating Your Rider Mower Using The Mower Brake Pedal Go PedalCutting Height Adjusting the Deck Seat PositionBlade Brake/PTO Wheel AlignmentBelt Replacement Servicing Your Rider MowerDeck Belt Fuse Replacement Lower Variable Speed BeltMaintaining Your Rider Mower General RecommendationsCutting Blade Oil Drain SleeveCleaning Engine LubricationFuel Filter OFF-SEASON Storage TROUBLE-SHOOTING Trouble Possible Cause Remedial ActionCharge with 6 Amp. charger until fully Parts List Model 325 Series Switch Plate Model 325 Series 735-0262 2216 712-3010 Hex Nut 5/16-18 714-0115 Description 683-0147 2718 Model 325 Series Hex Screw 5/16-24 x .75 Gr.5 List of color codes below. Please add Model 325 Series Spindle Assembly 683-0150C Flow Indicator Assembly Grass Bag Assembly Description Your Notes Your Notes MANUFACTURER’S Limited Warranty for