ENGLISH
OPERATING SAFETY RULES AND PRACTICES
Operator Responsibility
Safe operation is in the responsibility of the operator.
The operator shall be familiar with the operation and function of all controls and instruments before operating the unit. Before operating the unit, operators shall have read and be familiar with the oper- ator’s manual for the particular unit being operated and they shall also abide by the safety rules and practices in the following paragraphs.
Before operating any unit, the operator shall be familiar with unusual operating conditions which may require additional safety precautions or special operating instructions.
General
Before operating make sure the unit is in the operating position.
Do not start or operate the unit, any of its functions or attachments, from any place other than from the designated operators position.
Before leaving the operator’s position:
Abring the unit to a complete stop;
Bif the unit must be on an incline, block the wheels.
Maintain a safe distance from the edge of ramps, platforms, and other similar work- ing surfaces.
Do not add to, or modify the unit.
Do not block access to fire aisles, stair- ways or fire equipment.
Traveling
Yield the right of way to pedestrians and emergency vehicles such as ambulanc- es and fire trucks.
Cross railroad tracks at an angle wherev- er possible. Do not park closer than 6 ft (1800 mm) to the nearest rail of a railroad track.
Keep a clear view of the path of travel and observe for other traffic, personnel, and safe clearances.
Under all travel conditions, operate the unit at a speed that will pernit it to be brought to a stop in a safe manner.
Do not indulge in stunt driving or horse- play.
Slow down for wet and slippery floors. Before driving over a dockboard or bridge plate, be sure that it is properly se- cured. Drive carefully and slowly across
the dockboard or bridge plate, and never exceed its rated capacity.
When negotiating turns, reduce speed to a safe level consistent with the operating environment. Make the turns smoothly.
Operator care of the unit
If the unit is found to be in need of repair or in any way unsafe, or contributes to an unsafe condition, the matter shall be re- ported immediately to the user’s desig- nated authority, and the unit shall not be operated until it has been restored to safe operating condition.
If during operation the unit becomes un- safe in any way, the matter shall be re- ported immediately to the user’s designated authority, and the unit shall not be operated until it has been restored to safe operating condition.
Do not make repairs or adjustments un- less specifically authorized to do so.
MAINTENANCE AND RE- BUILD PRACTICES
Operation of the unit may be hazardous if maintenance is neglected or repairs, rebuilds, or adjustments are not per- formed in accordance with the manufac- turer’s design criteria. Therefore, maintenance facilities (on or off premis- es), trained personnel, and detailed pro- cedures shall be provided. Maintenance and inspection of the unit shall be performed in conformance with the following practices:
Aa schedules planned maintenance, lubrication, and inspection system shall be followed; consult the manu- facturer’s recommendations.
Bonly tranined and authorized person- nel shall be permitted to maintain, re- pair, adjust, and inspect the unit, and in accordance with manufacturer’s specifications.
Avoid fire hazards and have fire protec- tion equipment present in the work area. Do not use open pans of fuel or flamma- ble cleaning fluids for cleaning parts.
FIRE SAFETY STANDARD
Any unit not in safe operating condition shall be removed from service.
Fire Prevention: The unit shall be kept in a clean condition and reasonably free of lint, excess oil, and grease. Noncombus- tible agents are preferred for cleaning the unit. Flammable liquids [those having flash points at or above 100°F (37,8°C)] are not allowed. Precautions regarding toxicity, ventilation, and fire hazard shall
be appropriate for the agent or solvent used.
Nameplate Visibility: The unit type desig- nations as shown on the nameplate and the type markers shall not be covered over with paint so that their identification information is obscured.
Safety information for
!sweeper
Please ensure you read and note the following before using the unit!
Please notify the firm which sold you the unit if you find any transport damage whi- le unpacking it.
Before starting up, please read the ope- rating instructions for your unit and in particular, heed this safety information.
Practical operation
Before using, check that the unit and the working equipment are in good working order and are safe to operate. Do not use the unit unless it is in a perfect condition.
The sweeper is not suitable for sweeping up liquids. Do not sweep up burning or glowing objects, e.g. cigarettes, matches or similar.
Use sturdy gloves when removing glass, metal or other materials from the dirt con- tainer.
This unit is not suitable for sweeping up substances harmful to health.
It is forbidden to stay in the danger zone. It is prohibited to operate the unit in po- tentially explosive rooms.
Operation
The operator shall use the unit for its in- tended use. When operating the unit they shall take into consideration the local cir- cumstances and when working with the unit shall watch out for third persons, es- pecially children.
Attention: Crushing and cutting/shearing at belts, side brushes, containers and push handles.
The unit must not be operated by child- ren.
Transport
Securely fix the unit during transport.
Maintenance
Repairs may only be carried out by ap- proved customer service agents or by persons skilled in this field, who are fami- liar with all relevant safety regulations.
Accessories and spare parts
3