Stanley Black & Decker CS05/CS06 user manual Hose Types, Hose Safety Tags

Page 10

HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

D O N O T R E M O V E T H I S T A G

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

D O

 

 

 

 

 

 

 

 

 

 

N O

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

 

 

 

 

 

 

 

T

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

 

 

 

 

 

 

 

 

R E

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

 

 

 

 

 

 

 

 

 

M

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

 

 

 

 

 

 

 

O

 

ELECTRIC LINES.

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

 

E

 

 

 

 

 

 

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

 

 

 

 

 

 

 

T

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

H

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

I

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

S

 

 

 

 

 

 

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

 

T A

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

SEE OTHER SIDE

 

TRIC LINES.

 

 

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HAN- DLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACTAT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

SEE OTHER SIDE

 

SIDE 1

SIDE 2

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

10 ► CS05/CS06 User Manual

Page 9 Page 11
Image 10
Page 9 Page 11
Contents CS05 CS06 Page Table of Contents Safety Symbols Local Safety RegulationsSafety Precautions Safety Precautions Electrical Precautions Working in Proximity to Electrical HazardsStorm Work and Emergency CONDITIONS-LINE Clearance 107 Tool Stickers & TagsHose Safety Tags Hose TypesHose Recommendations Tool to Hydraulic Circuit Hose RecommendationsHtma Requirements Htma / Ehtma RequirementsOperating Procedures Preoperation ProceduresOperation Felling or Back CUT Felling Cutting Down a Tree FigureNotching or Undercutting BuckingLogs with Pressure on TOP Figure Crosscutting Logs with Pressure on TopLOGS/LIMBS with Pressure on Bottom Figure Crosscutting Logs/Limbs with Pressure on BottomCold Weather Operation Pruning and DebranchingTool Protection & Care Troubleshooting Problem Cause RemedySpecifications AccessoriesCS05/CS06 Parts Illustration CS05/CS06 Parts List Part QTY DescriptionParts List

CS05/CS06 specifications

Stanley Black & Decker has long been synonymous with quality and innovation in the industrial tools sector, and their CS05 and CS06 models exemplify this commitment. These two models represent some of the latest advancements in battery-powered electric tools designed for both professionals and DIY enthusiasts.

The Stanley Black & Decker CS05/CS06 models are engineered with a powerful motor that delivers impressive torque and speed, allowing users to tackle a variety of tasks with ease. The CS05 model typically features a 20V Max lithium battery system that provides longer run time and improved battery life, ensuring that users can complete their projects without interruption. This battery technology is particularly advantageous for high-demand applications, making it ideal for construction, woodworking, and metalworking.

One of the standout features of the CS05/CS06 is their ergonomic design. Both models boast a lightweight structure and well-balanced form, allowing for extended use without causing fatigue. The soft-grip handle enhances user comfort and control, making precision tasks much simpler. Additionally, the compact design of the tools aids in maneuverability in tight spaces, making them perfect for both professional and home environments.

In terms of technology, the CS05/CS06 incorporates advanced electronic controls that offer variable speed settings. This allows users to adjust the speed according to the specific requirements of the job, providing versatility that is essential for tackling various materials and applications. The built-in LED work light is another handy feature, illuminating dark areas or work surfaces to improve visibility and accuracy during use.

Durability is a prominent characteristic of the Stanley Black & Decker CS05 and CS06 models. Constructed with high-quality materials, both tools are designed to withstand the rigors of demanding job sites. The protective housing and robust components ensure longevity and reliable performance, even under extreme conditions.

Lastly, both models come equipped with features that enhance safety, including safety switches and guards that prevent accidental starts. The overall combination of strength, versatility, comfort, and safety makes the Stanley Black & Decker CS05/CS06 a top choice for anyone looking to invest in a reliable, high-performance electric tool. In today's ever-evolving market, these models stand out as examples of where quality meets innovation.
Top Page Image Contents