Stanley Black & Decker CS05/CS06 Operation, Preoperation Procedures, Operating Procedures

Page 13

OPERATION

PREOPERATION PROCEDURES

CHECK POWER SOURCE

1.Using a calibrated flowmeter and pressure gauge, check that the hydraulic power source develops a flow of 4-6 gpm/15-23 lpm at 1500-2000 psi/105- 140 bar for the CS05 or a flow of 7-9 gpm/26-34 lpm at 1000-2000 psi/70-140 bar for the CS06.

2.Make certain that the hydraulic power source is equipped with a relief valve set to open at 2100-­ 2250 psi/145-155 bar.

CONNECT HOSES

1.Wipe all hose couplers with a clean lint-free cloth before making connections.

2.Connect the hoses from the hydraulic power source to the tool fittings or quick disconnects. It is good practice to connect return hoses first and discon- nect them last to minimize or avoid trapped pressure within the tool.

3.Observe the arrow on the couplers to ensure that the flow is in the proper direction. The female cou- pler on the tool hose is the inlet (pressure) coupler.

4.Move the hydraulic circuit control valve to the “ON” position to operate the tool.

NOTE:

If uncoupled hoses are left in the sun, pressure in- crease inside the hose may make them difficult to connect. Whenever possible, connect the free ends of the hoses together.

SYSTEM SELECTION (OC/CC)

Saws configured with the system selector option require setup for the system, closed-center (CC) or open-center (CC), in which it will operate. The selector screw is lo- cated in the bottom end of the valve spool.

1.Determine the system type.

2.For operation in a CC system, turn the selector screw fully clockwise. When the selector screw bot- toms, CC operation is selected.

3.For operation in an OC system, turn the selector screw counter-clockwise until meeting resistance (from the retaining ring). Turn the selector screw clockwise and then counter-clockwise to be sure that you are sensing resistance of the retaining ring. Do not force the selector screw.

IMPORTANT

To prevent damage to the retaining ring, do not

attempt to force the selector screw counter-clockwise

beyond the point of initial resistance.

OPERATING PROCEDURES

The following are general wood cutting­ procedures and techniques. Differences­ in the terrain, vegetation, and type of wood will make this infor­mation more or less val- id for particu­lar areas. For advice on specific woodcut- ting problems or techniques for your area, consult your local Stanley representative or your county agent. They can often provide information­ that will make your work safer and more productive.

CUTTING TIPS

1.Check the lean of the tree. Tie a weight to a piece of string about 2 feet long. Hang the weight in your line of sight. The string is a good vertical line to help you judge the lean of the tree. The tree should fall the way it is leaning. Trees that are straight (leaning no more than 5 degrees) generally­ can be felled in any direction.

2.Avoid felling across another tree, log, rocks, gully or ridge. Do not fell straight uphill or downhill­. Fell the tree diagonally to the hill. Consider the wind direc- tion and velocity. Do not attempt cutting in strong winds.

3.Check the weight distribution. A tree is heavier on the side with the most limbs. It will try to fall on its heavy side. Trim a few limbs to “balance” the tree.

4.Clear the work area. You need a clean area all around the tree for good footing. Get every­thing out of the area where the tree will fall. Do not cut trees near structures. Because of the danger of electro- cution, use extreme care when cutting trees near power lines.

5.Before starting the cut, prepare your escape path. Make sure the escape path is clear of brush and branches. The escape path should be at an angle away from the direction of fall.

CS05/CS06 User Manual ◄ 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents CS05 CS06 Page Table of Contents Local Safety Regulations Safety SymbolsSafety Precautions Safety Precautions Working in Proximity to Electrical Hazards Electrical PrecautionsStorm Work and Emergency CONDITIONS-LINE Clearance Tool Stickers & Tags 107Hose Types Hose Safety TagsTool to Hydraulic Circuit Hose Recommendations Hose RecommendationsHtma / Ehtma Requirements Htma RequirementsOperating Procedures Preoperation ProceduresOperation Notching or Undercutting Felling Cutting Down a Tree FigureFelling or Back CUT BuckingCrosscutting Logs with Pressure on Top Logs with Pressure on TOP FigureCrosscutting Logs/Limbs with Pressure on Bottom LOGS/LIMBS with Pressure on Bottom FigurePruning and Debranching Cold Weather OperationTool Protection & Care Problem Cause Remedy TroubleshootingAccessories SpecificationsCS05/CS06 Parts Illustration Part QTY Description CS05/CS06 Parts ListParts List

CS05/CS06 specifications

Stanley Black & Decker has long been synonymous with quality and innovation in the industrial tools sector, and their CS05 and CS06 models exemplify this commitment. These two models represent some of the latest advancements in battery-powered electric tools designed for both professionals and DIY enthusiasts.

The Stanley Black & Decker CS05/CS06 models are engineered with a powerful motor that delivers impressive torque and speed, allowing users to tackle a variety of tasks with ease. The CS05 model typically features a 20V Max lithium battery system that provides longer run time and improved battery life, ensuring that users can complete their projects without interruption. This battery technology is particularly advantageous for high-demand applications, making it ideal for construction, woodworking, and metalworking.

One of the standout features of the CS05/CS06 is their ergonomic design. Both models boast a lightweight structure and well-balanced form, allowing for extended use without causing fatigue. The soft-grip handle enhances user comfort and control, making precision tasks much simpler. Additionally, the compact design of the tools aids in maneuverability in tight spaces, making them perfect for both professional and home environments.

In terms of technology, the CS05/CS06 incorporates advanced electronic controls that offer variable speed settings. This allows users to adjust the speed according to the specific requirements of the job, providing versatility that is essential for tackling various materials and applications. The built-in LED work light is another handy feature, illuminating dark areas or work surfaces to improve visibility and accuracy during use.

Durability is a prominent characteristic of the Stanley Black & Decker CS05 and CS06 models. Constructed with high-quality materials, both tools are designed to withstand the rigors of demanding job sites. The protective housing and robust components ensure longevity and reliable performance, even under extreme conditions.

Lastly, both models come equipped with features that enhance safety, including safety switches and guards that prevent accidental starts. The overall combination of strength, versatility, comfort, and safety makes the Stanley Black & Decker CS05/CS06 a top choice for anyone looking to invest in a reliable, high-performance electric tool. In today's ever-evolving market, these models stand out as examples of where quality meets innovation.
Top Page Image Contents