Motor Reassembly, Shafts | Stanley Black & Decker DS06 manual

SERVICE INSTRUCTIONS

groove should be smooth as should the rest of the ﬂ at surface.

The bore for the shaft seal should be smooth or oil leakage may occur.

GEAR HOUSING

Shake the gear housing and the two seal check balls (not shown) should rattle. If the seal balls do not rattle then they are probably plugged with contaminants and the gear housing will require replacement.

SHAFTS

The shaft diameter at the bearing and seal locations must be smooth. Grooves, roughness or a reduced diameter indicate ﬂ uid contamination or damaged bushings. Grit particles may have been imbedded in the bushings grind- ing into the hardened shaft. If abnormal shaft wear as above occurs (more than normal polishing), replace both the shaft and associated bushings.

Also check the hydraulic system for excess contamination in the ﬂ uid and for ﬁ lter condition. Operating conditions may require changing from a 25-micron ﬁ lter to an over- sized 10-micron ﬁ lter.

MOTOR REASSEMBLY

Refer to the illustration below for correct placement of parts.

1.If the bushings (6) were removed from the valve handle (22) and the gear housing (4), install new bushings using a p/n 11918 bearing pusher. (NOTE: The bushing split line must face the center of the gear housing).

Serial Number 356 and Below.

		54	53
		54
	13		8
			8
90			4

7 9

100			93	56
97	95	94	93	56

Serial Number 357 and Above.

	54			53
	13			53
	13
90				8
90
57				4
				4
91
92
98
47
100
48
58				9
				9
49
60				7
60
96	95	94	93	56

2.Grease and carefully install a new quad ring (90) into the seal liner (57). Grease and install a new o-ring (56) onto the seal liner. Install the seal liner into the valve handle assy (22). Replace the retaining ring (91).

3.To replace the bearing (92) onto the motor shaft (53), support the bearing inner race and press the motor shaft through the bearing inner race.

4.Place the valve handle assy on a smooth clean arbor press surface (protected from damage) with the large bear- ing bore facing up. Position the valve handle so a clearance hole exists for the insertion of the motor shaft.

5.Apply grease to the motor shaft, keyway and bush-

ing and then insert the motor shaft through the shaft seal. Using a socket with a diameter equal to the bearing O.D., press the bearing and motor shaft into place. Press only on the outer race.

6.Install the needle roller (54) in the keyway of the motor shaft. Use grease to keep the needle roller in place. Slide the drive gear (13) over the needle roller and shaft. Install the idler shaft (8) and gear (9).

7.Apply grease to the face seal o-ring groove; then install the o-ring (7).

8.Note the screw hole pattern on the rear gear housing and the valve handle. They will only assemble one way. With all parts aligned, carefully slide the gear housing as- sembly over the gears until it contacts the valve handle. Do not force parts together.

9.Turn the motor shaft manually to check for free rotation. Install the eight capscrews (1) and then recheck rotation.

DS06 specifications

Stanley Black & Decker DS06 is a powerful and versatile tool that combines cutting-edge technology with user-friendly features, making it a must-have for both professionals and DIY enthusiasts. Designed for optimal performance, the DS06 caters to a wide range of applications, from heavy-duty construction tasks to light home improvement projects.

One of the standout features of the DS06 is its robust motor. With a high power output, this tool delivers consistent performance, ensuring that users can tackle even the toughest materials with ease. The motor's efficiency not only enhances the tool's performance but also contributes to its longevity, allowing it to withstand rigorous use in demanding environments.

In addition to its powerful motor, the DS06 incorporates advanced battery technology. Equipped with a lithium-ion battery, this tool promises an extended runtime and reduced charging times compared to traditional batteries. Users can experience greater convenience, as the quick-charge capability means less downtime and more productivity. The battery's lightweight design also enhances the tool's overall ergonomics, making it more comfortable to handle during extended use.

Another significant characteristic of the DS06 is its intelligent design. Featuring an ergonomic grip, the tool is designed to reduce user fatigue, making it suitable for prolonged tasks. The lightweight construction of the DS06 ensures that users can maneuver the tool easily without compromising control.

Stanley Black & Decker has also prioritized safety with the DS06. It includes several safety features, such as a blade guard and a safety lock-off switch, which help prevent accidents during operation. These features provide peace of mind, allowing users to focus on their work without worrying about potential hazards.

Versatility is a key attribute of the DS06, with its ability to accommodate various attachments and accessories. This adaptability makes it a valuable addition to any tool collection, as it can be used for a wide array of tasks, including cutting, sanding, and drilling.

In summary, the Stanley Black & Decker DS06 is a tool that exemplifies innovation and practicality. Its powerful motor, advanced battery technology, ergonomic design, and safety features make it an ideal choice for a diverse range of applications. Whether you're a professional contractor or a weekend warrior, the DS06 is equipped to meet your needs and elevate your work efficiency.