Shindaiwa AH242es General maintenance, Muffler, Cutter blade adjustment Spark Plug, Fasteners

Page 14

General maintenance

IMPORTANT!

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY ECHO, INC. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFOR- MANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

NOTE:

Using non-standard replacement parts could invalidate your Shindaiwa warranty.

WARNING!

Before performing any mainte- nance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance.

WARNING!

Non-standard accessories, cut- ting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to per- sonal injury.

Muffler

This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss.

Cutter blade adjustment

Spark Plug

Keep the spark plug and wire connections tight and clean.

Fasteners

Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight.

WARNING!

The cutter blades are very sharp! Always wear gloves when working around the cutter assembly.

Cutting performance of your machine depends a great deal on proper cut- ter blade adjustment. Properly adjusted blades will oscillate freely yet help pre- vent binding of cut material between blades. Adjust blades as follows:

1.Loosen all blade locknuts at least one full turn.

2.Tighten each blade shoulder bolt firmly, and then loosen the shoulder bolts 1/4 to 1/2 turn.

3.Working from the gearcase end, lock each bolt in place by firmly tighten- ing its locknut while preventing the shoulder bolt from turning.

When shoulder bolt adjustment is cor- rect, there should be a gap of 0.25–0.50

mmbetween the cutter blades and the flat washers, and the flat washer beneath each bolt head should turn freely.

CAUTION!

Operating the trimmer with worn or improperly adjusted cutters will reduce cutter performance and may also damage your machine. Never operate the machine with damaged or worn cutters.

 

Locknut

Guide Bar

 

Cutter

 

Blades

Washer (should

Shoulder Bolt

turn freely)

 

Adjusting cutter blades

 

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents AH242 Articulated Hedge Trimmer Introduction ContentsSafety and Operational Labels Safety Operating Precautions Safety Equipment and Labels Operator SafetySpecifications Product DescriptionAdjusting the Hedge Trimmer Cutter Assembly AssemblyPrior To Assembly Emission Control Exhaust & EvaporativeCutter Assembly Positions Throttle trigger free playMixing Fuel Examples of 501 mixing quanti- tiesMixing Instructions Filling the Fuel TankStarting the Engine After useSlide the ignition switch to the on position Checking Unit Condition When the Engine StartsStopping the Engine Starting a flooded engineCutting Sequence Using the Hedge Trimmer PreparationsOperation Cutting TechniquesMuffler General maintenanceCutter blade adjustment Spark Plug FastenersHour maintenance MaintenanceDaily maintenance 10/15-Hour maintenanceGearcase lubrication Gearcase Grease fitting Engine Break-In Carburetor AdjustmentMuffler and spark arrester maintenance High Altitude OperationLong Term Storage Adjusting Engine IdleIdle Speed Adjustment Troubleshooting Guide Engine is knocking Poor acceleration Engine stops abruptlyExceptions Purchased Repair Parts and Accessories 01/2010 Page Page Servicing Information Parts/Serial Number

AH242es, AH242, X7502801000 specifications

The Shindaiwa AH242 and AH242es are advanced two-stroke, gasoline-powered hedge trimmers known for their power and efficiency. These models are designed for both professional landscapers and homeowners, featuring an ergonomic design that allows for extended use without fatigue. The AH242 is characterized by its lightweight construction, weighing only 11.5 lbs, making it easy to maneuver while trimming hedges and shrubs.

One of the standout features of the AH242 is its powerful 21.2cc engine, which delivers outstanding performance while maintaining low emissions. This is achieved through Shindaiwa's refined two-stroke technology, which not only enhances fuel efficiency but also reduces harmful exhaust fumes, contributing to a cleaner working environment. The AH242es version offers similar specifications but includes an Easy Start system, making it easier to start the machine with minimal effort, thus increasing user convenience.

Both models feature a double-sided cutting blade that measures 24 inches, providing an optimal cutting range and ensuring efficiency in trimming dense foliage. The design of the blade incorporates precision grinding technology, resulting in sharp edges that facilitate clean cuts and reduce the risk of plant damage. Moreover, the unique blade design minimizes vibration during operation, enhancing operator comfort and control.

The Shindaiwa AH242 and AH242es also boast an adjustable throttle control, allowing users to manage cutting speed according to the task at hand. This feature not only improves efficiency but also enhances safety by reducing the risk of accidental damage to surrounding plants. Additionally, the models incorporate a durable construction with high-quality materials, ensuring longevity and reliability in various weather conditions.

In terms of maintenance, both hedge trimmers are designed for easy accessibility to critical components, ensuring that servicing can be performed without hassle. The air filter can be easily accessed and cleaned, promoting engine longevity and optimal performance.

Overall, the Shindaiwa AH242, AH242es, and the associated model X7502801000 reflect a commitment to quality engineering, user comfort, and environmental responsibility. Whether for professional landscaping work or home gardening, these hedge trimmers provide powerful performance, innovative technology, and exceptional reliability, making them a top choice in the industry.
Top Page Image Contents