Shindaiwa 81606, T272X/EVC, T272/EVC manual Maintenance

Page 14

Maintenance

General Maintenance

IMPORTANT!

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PER- FORMED BY ANY REPAIR ESTABLISH- MENT OR INDIVIDUAL; HOWEVER, WAR- RANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA CORPORA- TION THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUT- COME OF A WARRANTY CLAIM.

WARNING!

Before performing any maintenance, repair, or cleaning work on the machine, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance work.

Muffler

This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connec- tions tight and clean.

Fasteners

Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight.

NOTE:

Using non-standard replacement parts could invalidate your Shindaiwa warranty.

WARNING!

Non-standard parts may not operate properly with your unit and may cause damage and lead to personal injury.

Blades

Keep blades sharp and check blade condition frequently. If a blade’s per- formance changes suddenly, stop the engine and check the blade for cracks or other damage. Replace a damaged blade IMMEDIATELY!

WARNING!

■Blades are not interchangeable between Shindaiwa edgers and trim- mer/brushcutter models. Operating any unit with a blade or attachment not approved for that unit can be haz- ardous and may cause serious injury.

■DO NOT use 2-tooth or NON- Shindaiwa approved 4-tooth cut- ting blades on Shindaiwa trimmers or brushcutters.

■Never repair a damaged blade by welding, straightening, or by modi- fying its shape. An altered blade may break during operation, result- ing in serious personal injury.

Daily Maintenance

 

 

 

Prior to each work day, perform the

■ Carefully remove any accumulations of

■ Check for loose or missing screws or

following:

dirt or debris from the muffler and fuel

components. Make sure the cutting

■ Remove the dirt and debris from the

tank. Dirt buildup in these areas can

attachment is securely fastened.

lead to engine overheating, fire, or pre-

■ Check the machine for leaking fuel or

engine, check the cooling fins and air

mature wear.

grease.

cleaner for clogging, and clean them

 

 

 

as necessary.

 

 

10 Hour Maintenance

Perform more frequently in dusty or dirty conditions.

■Remove the air cleaner filter. Clean or replace as necessary. To clean filter wash it thoroughly in soap and water. Let it dry before reinstalling the filter.

CAUTION!

Do not operate the machine if the air cleaner or element is damaged, or if the element is water-soaked.

Remove and clean or replace the element

Figure 27

10/15 Hour Maintenance

■Remove and clean the spark plug. Adjust the spark plug electrode gap to 0.6 - 0.7mm. If the plug must be replaced, use only Champion CJ8Y.

■Keep the spark plug wire connections tight and clean.

0.6 - 0.7mm

CAUTION!

Before removing the spark plug, clean the area around the plug to prevent dirt and dust from getting into the engine’s internal parts.

Figure 28

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents T272/EVC Trimmer T272X/EVC Trimmer Contents IntroductionWork Safely General Safety InstructionsSafety Labels Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentSpecifications T272/T272X Product DescriptionAdjusting Throttle Level Free Play T272/T272X AssemblyPrior to Assembly Handle T272/T272XSub-Shield T272X Install trimmer headCutting Attachment Shield T272/T272X Never operate the T272X without the safety clip in place Mount the Cutting Blade T272XExamples of 501 mixing quantities Mixing fuelFilling the fuel tank Minimize the Risk of FireSet the choke lever to the Closed posi When the Engine StartsStarting the Engine Stopping the Engine Engine Idle AdjustmentIdle Speed Adjustment Checking Unit ConditionOperation Brushcutter Shoulder Strap Using a Blade T272XUsing a Blade Blade ThrustMaintenance Fuel Filter Maintenance Shindaiwa Tornado Blade Long Term StorageBlade Sharpening Multiple-tooth Circular BladeTroubleshooting Guide What To Check Possible Cause RemedyLOW Power What To Check Engine stops abruptlyEmission System Warranty Statement Consiguientes Daños Por administrada es garantía EstaEmisión de Sistema del Garantía de Declaración Garantía Esta Por Cubierto Está QueContinuación Diagnostico Guia 19SPRemedio Causa Posible Revisar Qué 18SPDiagnostico Guia 17SPMúltiples Dientes de Discos Discos de AfiladoPlazo Largo de Almacenamiento Dvertencia¡AHoras-50 Cada Mantenimiento Continuación MantenimientoHoras-135 Cada Mantenimiento 15SPMantenimiento Continuación Operación Operación Motor del Parada Unidad La De Condición La VerifiqueMotor del Mínima Marcha de Ajuste 10SP Motor del ArranqueMotor el arranca Cuando Incendios! de riesgo el Disminuya Combustible de Tanque el LlenandoCombustible de Mezcla De proporción a mezclaT272X Disco/Cuchilla Ensamblaje Corte de Cuchilla la MonteEnsamblaje Mango el Ajustar Para EnsamblajeAcelerador del Palanca la de Holgura la de Ajuste T272/T272X Mango5SP T272X/C272 EspecificacionesProducto del Descripción 4SP Trabajo de Area del Alerta EstéEquipado Debidamente Operario El Juicio Buen Use Seguridad de EtiquetasSeguridad de Generales Instrucciones Alerta MantengaseSeguridad de Declaraciones Introducción 11/06 .Rev 81606 part de Numero
Top Page Image Contents