Shindaiwa T231X/EVC, T231/EVC Assembly and Adjustments, Handle, Adjust Throttle Lever Free Play

Page 6

Assembly and Adjustments

This unit comes fully assembled with the exception of the cutting attachment shield and cutting attachment.

Prior to Assembly

Before assembling, make sure you have all the components required for a com- plete unit and inspect unit and compo- nents for any damage.

nEngine and shaft assembly

nCutting attachment shield

nCutting attachment

nKit containing cutting attachment shield mounting bracket and hardware, this owner's/operator's manual and tool kit for routine maintenance. Tool kits vary by model and may include a hex wrench set, a spark plug/screw- driver combination wrench, and a span- ner.

IMPORTANT!

The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal

operation.

Handle

1.The handle is attached to the outer tube at the factory and positioned in an off-set position. See Figure 5.

2.Loosen the 4 socket-head cap screws on the handle and rotate the handle until the barrier bar is positioned hori- zontally on the left side of the unit. See Figure 6.

3.Position the handle forward of the Handle Positioning Label at the best position for operator comfort (usually about 10 inches ahead of the throttle housing).

4.Secure the handle by alternately tight- ening the four socket-head cap screws in a diagonal or “criss-cross” fashion.

Barrier

Bar

Handle

Outer

Tube

 

23101

 

4 Socket-head Cap-

Figure 5

screws

 

Handle

Handle Positioning Label

Outer

Tube

Barrier

Bar

23102

4 Socket-head Cap-

screws

Figure 6

Adjust Throttle Lever Free Play

The throttle lever free play should be approxiamtely 3/16-1/4 inch(4-6 mm). See Figure 7. Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever freeplay, follow the procedures and illustrations that follow.

23103

3/16-1/4 inch (4-6 mm)

Throttle Freeplay

Figure 7

Throttle Cable

Lock Nuts

23104

Figure 8

1.Loosen the throttle cable lock nuts and adjust in or out to achive proper free play of 3/16-1/4 inch(4-6 mm). See Figure 8.

2.Retighten the locknuts.

Image 6
Contents T231/EVC Trimmer T231X/EVC Trimmer Part Number 81601 Rev /06Contents IntroductionStay Alert General Safety Instructions The Properly Equipped OperatorWork Safely Minimize the Risk FireSafety Labels Be Aware of the Working EnvironmentSpecifications Product DescriptionPrior to Assembly Assembly and AdjustmentsAdjust Throttle Lever Free Play HandleInstall the Cutting Attachment Shield Assembly Cutting Attachment ShieldAssembly Trimmer Head Install the Trimmer HeadAssembly Blade T231X Never operate the T231X without the safety clip in placeMount the Cutting Blade Starting the Engine Mixing FuelFilling the Fuel Tank Examples of 501 mixing quantitiesWhen the Engine Starts Adjusting Engine IdleCutting attachment may rotate when the engine is started Idle Speed AdjustmentChecking Unit Condition Shoulder StrapCutting Grass-Units Equipped with a Trimmer Head Brushcutter Handlebar Using a Blade T231XBlade Thrust Brushcutter Shoulder StrapGeneral Maintenance Daily MaintenanceHour Maintenance 10/15-Hour Maintenance Blade Sharpening Hour MaintenaceLong Term Storage Shindaiwa Tornado BladeTroubleshooting Guide Possible CauseLOW Power Output Additional Problems Emission System Warranty Statement Fax 503 Telephone 81-82-849-2481 Notas Emisión de Sistema del Garantía de Declaración Continuación Diagnóstico Guía Causa Posible Revisar Que Diagnóstico Guía Horas-135 Cada Mantenimiento Discos de AfiladoPlazo Largo de Almacenamiento Múltiples Dientes de DiscosTodo de condición la inspeccione Horas-50 Cada MantenimientoHoras-10/15 Cada Mantenimiento Polvorientas o suciasHoras-10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento T231X Disco un Usando Corte de Cabezal con Equipadas Máquinas Césped de Corte Arnés de CorreaUnidad la de Condición la Verifique Continuación Motor del Arranque Motor del Mínima Marcha de AjusteMotor del Parada Mínima Marcha de AjusteCombustible de Mezcla Motor del ArranqueCombustible de Tanque el Llenando Incendios! deT231X Disco/Cuchilla Ensamblaje Corte de Cuchilla la MonteCorte de Cabezal Ensamblaje Corte de Accesorio del Protector EnsamblajeCorte de cuchilla la de posición la cambiar Para Ajustes y Ensamblaje Acelerador del holgura la AjusteMango Trabadoras tuercas las AjusteEspecificaciones Producto del DescripciónAutorizadas no Alteraciones o Modificaciones haga No Seguridad de Etiquetas PíesTrabajo de Area del Alerta Esté Incendios de Riesgo El Disminuya ¡ADVERTENCIA Juicio BuenUse ¡ADVERTENCIA Alerta MantengaseContenido Seguridad De Declationes IntroducciónPrecaución Shindaiwa Propietario/Operador Del Manual 11/06 .Rev 81601 parte de Número