Shindaiwa LE242 Using a Hand-held Edger, Adjusting the Cutting Depth, To adjust blade height

Page 10

Using a Hand-held Edger

Guidelines for Operating the Edger

Before edging, make sure the area is soft enough so the blade does not bog down. If necessary, water the area before edging.

Remove debris and other obstacles that could be thrown by the rotating blade.

Plan your work so the edger blade is always on your right-hand side.

Begin each pass by positioning the unit over the work, and with the engine run- ning at about half-throttle. Slowly lower the blade to the ground while applying full throttle. See Figure 16.

Do not move the edger into the work so fast that the engine or blade bogs down.

CAUTION!

Low-speed edging can lead to prema- ture clutch failure.

Do not pull the unit backward over the ground with the engine running. Doing so will tend to bury the blade.

Regular and frequent use of the edger will make a neater lawn, and a frequently trimmed edge will be easier to maintain.

Figure 16

WARNING!

nWear eye protection, long pants, and boots when operating this machine!

nWhenever you strike a hard object with the blade, always stop the edger and carefully inspect the blade for damage. NEVER OPERATE THE EDGER WITH A DAMAGED BLADE!

Adjusting the Cutting Depth

 

Guide Wheel

 

 

Adjusting knob

 

Guide Wheel

 

 

 

The numbers are for

 

 

reference only; they do

 

Figure 17a

NOT refer to depth in

Figure17

inches

 

10

 

 

The edger’s depth of cut is controlled by a combination of operator height, blade wear, and the positioning of the edger’s guide wheel.

To adjust blade height:

1.Loosen the guide wheel adjusting knob. See Figure 17.

2.Raise or lower the guide wheel to the desired setting. See Figure 17a.

3.Tighten the guide wheel adjusting knob firmly . See Figure 17.

WARNING!

Never adjust the guide wheel while the engine is running.

NOTE

Guide wheel adjustment is also required to compensate for blade wear.

WARNING!

Use only Shindaiwa replace- ment edger blades.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents LE242 Lawn Edger Contents Safety InstructionsIntroduction Safety Instructions Properly Equipped Operator Use Good JudgmentSafety Labels Be Aware of the Working EnvironmentPrior to Assembly SpecificationsProduct Description Adjust Throttle Lever Free Play Assembly and Adjustments Install Gearcase AssemblyAssembly and Adjustments Reinstall the air cleaner coverFilling the Fuel Tank Mixing FuelExamples of 501 mixing quantities When the Engine Starts Slide the ignition switch to the on position. See FigureStarting the Engine Checking Unit Condition Idle Speed AdjustmentStopping the Engine Use only authorized Shindaiwa partsTo adjust blade height Using a Hand-held EdgerAdjusting the Cutting Depth Guidelines for Operating the EdgerDaily Maintenance General MaintenanceHour Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceLubricate the Flexible Shaft With an authorized Shindaiwa servicing Inspect the Gearcase ProtectorDealer Replacing the Edger Blade Long Term StorageTroubleshooting Guide Engine does not StartAdditional Problems Emission System Warranty Statement Page 2220-849-82-81 Teléfono Com.shindaiwa.www 2481-849-82-81 FaxJapan 3167,-731 6696-692 Fax Emisión de Sistema del Garantía de Declaración Continuación Diagnostico Guia Adicionales ProblemasDiagnostico Guia Potencia BajaPolvo de libre Plazo Largo de AlmacenamientoOrilladora la de Cuchilla la Reemplazar Bujía la ReínstaleContinuación Horas 50 Cada Mantenimiento Mantenimiento horas 135 CadaEngranajes de Caja la de Protector el Inspeccione Horas 10/15 Cada Mantenimiento Horas 50 Cada MantenimientoPrecaución Sujetadores Diario MantenimientoGeneral Mantenimiento BujíaMano de Orillador el Utilizando Corte del Profundidad la AjustandoShindaiwa marca de lador Oril para cuchillas sólo Utilice Motor del Parada Unidad la de Condición la VerifiqueMotor del Mínima Marcha de Ajuste ApagadoOperación de posición la Motor del Arranque…motor el arranca Cuando Desde motor el arranque NuncaDe proporción Combustible de Tanque el LlenandoPRECAUCIÓN!¡ Combustible de Mezcla Ajustes y Ensamblaje Acelerador del Holgura la AjusteEngranaje de Caja la de Instalación De normal operación la durante operador EspecificacionesEnsamblar de Antes Autorizadas no teraciones Al o modificaciones haga NoSeguridad de Etiquetas Trabajo de Area del Alerta EstéJuicio Buen Use ¡ADVERTENCIA Descalzo! máquina laDe Riesgo El Disminuya ContenidoIncendios Cuidado con TrabajeRev 81532 pieza de Número

81532, LE242 specifications

The Shindaiwa 81532 LE242 is a powerful and versatile tool designed for landscape professionals and homeowners alike. Known for its reliability and performance, the LE242 is a lightweight and efficient string trimmer that can tackle a range of tasks, from trimming grass to maintaining garden beds.

One of the standout features of the LE242 is its engine. It is powered by a 21.2cc, 2-stroke, low-emission engine that provides ample power for cutting through thick grass and weeds. The engine's design is optimized for fuel efficiency, allowing users to work longer without constant refueling. This is crucial for landscaping professionals who need to maximize productivity throughout the day.

Ergonomics is another focal point in the design of the LE242. It comes equipped with a comfortable and adjustable handlebars, allowing users to maintain a natural posture while working. The lightweight design of the trimmer, weighing in at approximately 10.8 lbs, reduces user fatigue, making it easier to maneuver over extended periods.

The Shindaiwa LE242 also boasts an advanced starting system. The Easy Start feature minimizes the effort required to pull-start the engine, ensuring that users can get to work without frustration. This feature is particularly appreciated by those who may not be experienced with outdoor power equipment.

In terms of cutting technology, the LE242 is designed with a commercial-grade cutting head that allows for quick line replacement and easy maintenance. The dual-line system provides a wider cutting path, increasing efficiency and reducing the amount of time needed to complete tasks. Additionally, it allows for the use of various line sizes, catering to different cutting needs.

Durability is a key characteristic of Shindaiwa products, and the LE242 is no exception. Built with high-quality materials, it withstands rigorous use and harsh conditions typical of professional landscaping environments. The trimmer's components are designed to resist wear and tear, ensuring a long lifespan with proper care.

In summary, the Shindaiwa 81532 LE242 combines power, efficiency, and user-friendly design, making it an excellent choice for both professionals and DIY landscapers. With its reliable engine, ergonomic features, and durable construction, the LE242 stands out in the competitive market of string trimmers. Whether maintaining large lawns or delicate garden beds, the LE242 is equipped to handle it all with ease.
Top Page Image Contents