Shindaiwa LE242 Starting the Engine, Slide the ignition switch to the on position. See Figure

Page 8

Starting the Engine

IMPORTANT!!

Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP.

ON

Figure 9

1.Slide the ignition switch to the “ON” position. See Figure 9.

Return Tube

Primer Bulb

Figure 10

2.Press the primer bulb until fuel can be seen flowing in the transparent return tube.

IMPORTANT!

The primer system only pushes fuel through the carburetor. Repeatedly pressing the primer bulb will not flood the engine with fuel.

3.Set the choke lever to the CLOSED position if engine is cold.

Closed

Figure 11

Make sure the cutting attach- ment

is clear of ob-

structions!

Figure 12

4.While holding the outer tube firmly with left hand. Use your other hand to slowly pull the recoil starter handle until resis- tance is felt, then pull quickly to start the engine.

CAUTION!

Do not pull the recoil starter to the end of the rope travel. Pulling the recoil starter to the end of the rope travel can damage the starter.

WARNING!

The cutting attachment may rotate when the engine is started!

5.When the engine starts, slowly move the choke lever to the “OPEN” position. See Figure 13. (If the engine stops after the initial start, close the choke and restart.)

Open

Figure 13

WARNING!

Never start the engine from the operating position.

IMPORTANT!

If the engine fails to start after several at- tempts with the choke in the closed posi- tion, the engine may be flooded with fuel. If flooding is suspected, move the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

When the Engine Starts...

nAfter the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit.

nAdvancing the throttle makes the cut- ting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting Engine Idle” on next page).

Page 7 Page 9
Image 8
Page 7 Page 9
Contents LE242 Lawn Edger Introduction Safety InstructionsContents Safety Instructions Properly Equipped Operator Use Good JudgmentSafety Labels Be Aware of the Working EnvironmentProduct Description SpecificationsPrior to Assembly Assembly and Adjustments Install Gearcase Assembly Assembly and AdjustmentsAdjust Throttle Lever Free Play Reinstall the air cleaner coverExamples of 501 mixing quantities Mixing FuelFilling the Fuel Tank Starting the Engine Slide the ignition switch to the on position. See FigureWhen the Engine Starts Idle Speed Adjustment Stopping the EngineChecking Unit Condition Use only authorized Shindaiwa partsUsing a Hand-held Edger Adjusting the Cutting DepthTo adjust blade height Guidelines for Operating the EdgerHour Maintenance General MaintenanceDaily Maintenance Lubricate the Flexible Shaft 10/15-Hour MaintenanceEvery 10 to 15 hours of operation Dealer Inspect the Gearcase ProtectorWith an authorized Shindaiwa servicing Replacing the Edger Blade Long Term StorageTroubleshooting Guide Engine does not StartAdditional Problems Emission System Warranty Statement Page Japan 3167,-731 6696-692 Fax 2481-849-82-81 Fax2220-849-82-81 Teléfono Com.shindaiwa.www Emisión de Sistema del Garantía de Declaración Continuación Diagnostico Guia Adicionales ProblemasDiagnostico Guia Potencia BajaPlazo Largo de Almacenamiento Orilladora la de Cuchilla la ReemplazarPolvo de libre Bujía la ReínstaleEngranajes de Caja la de Protector el Inspeccione Mantenimiento horas 135 CadaContinuación Horas 50 Cada Mantenimiento Precaución Horas 50 Cada MantenimientoHoras 10/15 Cada Mantenimiento Diario Mantenimiento General MantenimientoSujetadores BujíaShindaiwa marca de lador Oril para cuchillas sólo Utilice Corte del Profundidad la AjustandoMano de Orillador el Utilizando Unidad la de Condición la Verifique Motor del Mínima Marcha de AjusteMotor del Parada ApagadoMotor del Arranque …motor el arranca CuandoOperación de posición la Desde motor el arranque NuncaPRECAUCIÓN!¡ Combustible de Mezcla Combustible de Tanque el LlenandoDe proporción Engranaje de Caja la de Instalación Acelerador del Holgura la AjusteAjustes y Ensamblaje Especificaciones Ensamblar de AntesDe normal operación la durante operador Autorizadas no teraciones Al o modificaciones haga NoSeguridad de Etiquetas Trabajo de Area del Alerta EstéJuicio Buen Use ¡ADVERTENCIA Descalzo! máquina laContenido IncendiosDe Riesgo El Disminuya Cuidado con TrabajeRev 81532 pieza de Número

81532, LE242 specifications

The Shindaiwa 81532 LE242 is a powerful and versatile tool designed for landscape professionals and homeowners alike. Known for its reliability and performance, the LE242 is a lightweight and efficient string trimmer that can tackle a range of tasks, from trimming grass to maintaining garden beds.

One of the standout features of the LE242 is its engine. It is powered by a 21.2cc, 2-stroke, low-emission engine that provides ample power for cutting through thick grass and weeds. The engine's design is optimized for fuel efficiency, allowing users to work longer without constant refueling. This is crucial for landscaping professionals who need to maximize productivity throughout the day.

Ergonomics is another focal point in the design of the LE242. It comes equipped with a comfortable and adjustable handlebars, allowing users to maintain a natural posture while working. The lightweight design of the trimmer, weighing in at approximately 10.8 lbs, reduces user fatigue, making it easier to maneuver over extended periods.

The Shindaiwa LE242 also boasts an advanced starting system. The Easy Start feature minimizes the effort required to pull-start the engine, ensuring that users can get to work without frustration. This feature is particularly appreciated by those who may not be experienced with outdoor power equipment.

In terms of cutting technology, the LE242 is designed with a commercial-grade cutting head that allows for quick line replacement and easy maintenance. The dual-line system provides a wider cutting path, increasing efficiency and reducing the amount of time needed to complete tasks. Additionally, it allows for the use of various line sizes, catering to different cutting needs.

Durability is a key characteristic of Shindaiwa products, and the LE242 is no exception. Built with high-quality materials, it withstands rigorous use and harsh conditions typical of professional landscaping environments. The trimmer's components are designed to resist wear and tear, ensuring a long lifespan with proper care.

In summary, the Shindaiwa 81532 LE242 combines power, efficiency, and user-friendly design, making it an excellent choice for both professionals and DIY landscapers. With its reliable engine, ergonomic features, and durable construction, the LE242 stands out in the competitive market of string trimmers. Whether maintaining large lawns or delicate garden beds, the LE242 is equipped to handle it all with ease.
Top Page Image Contents