Shindaiwa 81644 manual Long Term Storage, Blade Sharpening, Shindaiwa Tornado Blade

Page 17

Long Term Storage

Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare it for storage:

nClean external parts thoroughly.

nDrain all the fuel from the fuel tank.

IMPORTANT!

All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL™,

if oil with fuel stabilizer is not used.

CAUTION!

Gasoline stored in the carburetor for extended periods can cause hard starting and could also lead

to increased service and maintenance cost.

nRemove the remaining fuel from the fuel lines and carburetor.

1.Prime the primer bulb until no more fuel is passing through.

2.Start and run the engine until it stops running.

3.Repeat steps 1 and 2 until the engine will no longer start.

nRemove the spark plug and pour about 1/4 ounce of 2-cycle mixing oil into the cylinder through the spark plug hole.

Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug.

nBefore storing the unit, repair or replace any worn or damaged parts.

nRemove the air cleaner element from the carburetor and clean it thoroughly with soap and water. Let dry and reassemble the element.

nStore the unit in a clean, dust-free area.

Blade Sharpening

When the cutting edges of the blade be- come dull, they can be resharpened with a few strokes of a file.

In order to keep the blade in balance, all cutting edges must be sharpened equally.

Shindaiwa Tornado™ Blade

To sharpen the cutters on a Shindaiwa Tor- nado Blade, use a 7/32-inch round file. File the leading edge of each tooth to a razor edge. The top plate of each tooth should angle back 30°.

Round

File

30°

Figure 31

WARNING!

Sharpen only the cutting teeth of a blade. DO NOT alter the contour of the blade in any way.

Multiple-tooth Circular Blade

Use a round file to maintain a radius of 0.04 to 0.06" (1 to 1.5 mm) at the base of each tooth. Cutting edges must be offset equally on each side.

Round

File

Figure 32

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents C242 Brushcutter Introduction ContentsSafety Instructions Always use the proper cutting tool for the job Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsProduct Description Specifications C242Prior to Assembly Sub-Shield C242 AssemblyCutting Attachment Shield Adjust Throttle Lever Free Play AdjustmentsHandle Bar C242 Install the handlebar With the gear case output shaft facing Installing a Trimmer HeadBoth holders must be flat against the surface of the blade Installing a BladeFilling the Fuel Tank Mixing FuelStarting the Engine Examples of 501 mixing quantitiesCutting attachment may rotate when the engine is started Adjusting Engine IdleWhen the Engine Starts Idle Speed AdjustmentCutting Grass-Units equipped with a trimmer head Checking Unit ConditionShoulder Strap C242 Operating Units with a Blade Using a Blade C242Hour Maintenance General MaintenanceDaily Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceDealer With an authorized Shindaiwa servicingBlade Sharpening Long Term StorageShindaiwa Tornado Blade Multiple-tooth Circular BladeEngine does not Start Troubleshooting GuideAdditional Problems Manufacturers Warranty Coverage Limitations 2220-849-82-81 Telephone 6696-692 2481-849-82-81 FaxJapan 3167,-731 3070-692 Hiroshima Ku,-AsaminamiAdicionales Problemas Continuación Diagnostico Guia18SP Diagnostico GuiaPlazo Largo de Almacenamiento Discos de AfiladoMúltiples Dientes de Discos Tornado Shindaiwa DiscoShindaiwa autorizado buidor Mantenimiento horas 135 CadaDistri o servicio de centro su con consulte Carbón, de excesiva acumulación nota SiHoras 10/15 Cada Mantenimiento Horas 50 Cada MantenimientoGeneral Mantenimiento Horas 10 Cada MantenimientoDiario Mantenimiento C242 Disco un Usando Cuchilla una con Unidades OperandoUnidad la de Condición la Verifique Corte deCabezal con Equipadas Máquinas Césped de Corte Mínima Marcha de Ajuste Motor delMotor del Parada Continuación Motor del ArranqueCombustible de Tanque el Llenando Motor del ArranqueCombustible de Mezcla De proporción9SP Cuchilla la InstalandoNylon de Cabezal del Instalación C242 Mango Continuación EnsamblajeAcelerador del holgura la Ajuste Ajustes Allen cabeza EnsamblajeEnsamblar de Antes C242 EspecificacionesProducto del Descripción Trabajo de Area del Alerta Esté Seguridad de EtiquetasPíes Limpios mangos los mantenga Siempre Equipado Debidamente Operario El Seguridad de InstruccionesIncendios de Riesgo El Disminuya ContenidoHumana reproducción la Nocivos efectos otros u congénitos Alerta MantengaseC242 Desmalezadora

81644 specifications

The Shindaiwa 81644 is a remarkable piece of equipment designed for professionals in landscaping and agriculture. Renowned for its durability and performance, this model is an essential tool for anyone in need of a reliable, high-efficiency solution for their yard care and maintenance projects.

One of the standout features of the Shindaiwa 81644 is its powerful engine. The unit is equipped with a robust 25.4 cc 2-stroke engine that delivers an impressive power-to-weight ratio, ensuring efficient operation without compromising on performance. This kind of engine is designed for easy starting and provides a reliable output that allows users to tackle even the most challenging tasks with ease.

Another key characteristic of the Shindaiwa 81644 is its lightweight design. Weighing in at approximately 7.9 lbs, this model is designed to reduce operator fatigue, allowing for extended use without added strain. The ergonomic handle further enhances comfort, enabling a natural grip and offering better control during operation.

Technologically, the Shindaiwa 81644 incorporates advanced anti-vibration technology. This feature minimizes vibrations during use, ensuring a smoother experience while reducing the risk of operator fatigue. Additionally, the unit includes an adjustable throttle, allowing users to optimize their cutting speed based on the specific job at hand.

The durability of the Shindaiwa 81644 is another highlight. Constructed with high-quality materials, this equipment is built to withstand the rigors of regular use in various weather conditions. Its fuel-efficient engine also represents Shindaiwa's commitment to sustainability, minimizing environmental impact while maximizing performance.

For convenience, the Shindaiwa 81644 is designed with an easy-to-access air filter and spark plug, simplifying maintenance. This ensures that operators can keep their equipment in top condition with minimal effort.

In summary, the Shindaiwa 81644 combines power, efficiency, and user-friendly features, making it one of the most sought-after options for professionals looking to enhance their landscaping tools. Whether for commercial or personal use, this model stands out as a reliable choice that meets the demands of any outdoor maintenance project.
Top Page Image Contents