Servis-Rhino 2412 manual Standard Equipment and Specifications

Page 47

OPERATION

1.Standard Equipment and Specifications

Specifications will vary with tractor, tire size, hydraulic system and bucket used. The specifications are given for a loader equipped with 84” material bucket operated with an average tractor hydraulic system of 25.8 GPM with engine operating at 2300 RPM and control valve relief setting of 2750 PSI.

Horsepower Range		90-130 HP
System pressure/flow rate		2750 PSI/ 25.8 GPM
Lift Capacity to maximum height		3056 lbs.
Breakout force at pivot pin		8240 lbs.
Rollback force at ground line		7244 lbs.
Total weight with bucket (approx.)		2060 lbs.
Raising time to full height		5.36 seconds
Lower time		4.34 seconds
Attachment dump time		4 seconds
Attachment rollback time		3.56 seconds
Hydraulic system flow		25.8 GPM
System pressure at rated flow		2750 PSI
(A)	Maximum Clearance at Full Height	149.5”
(B)	Clearance with Bucket Dumped	117”
(C)	Reach at Maximum Height	39.69”
(D)	Maximum Dump Angle	50°
(E)	Reach with Attachment on Ground	89.5”
(F)	Attachment Rollback Angle	13°
(G)	Digging Depth	4”
(H)	Overall Height in Carry Position	80”

(Manufacturers estimated specifications and design subject to change without notice.)

2412 01/11

Operation Section 4-3

© 2011 Alamo Group Inc.

OPERATION

Image 47

Contents 2412 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety2412 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 2412 01/11 Safety Section Safety SL-33 Safety 2412 01/11 Safety Section Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety See Your Rhino Dealer Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 2412 01/11 Safety Section Loader Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyAssembly Proper Ballasting and Wheel Spacing Assembly 2412 01/11 Assembly Section Dismounting Loader Dismounting Loader and Mounting Loader to TractorFor Loader Plumbed to Tractor Remote Valve Preparing Stored Loader for MountingMounting Procedure Page Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor Lighting and SMV Emblem Tractor RequirementsRops and Seat Belt Tractor Ballast Getting On and Off the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Pre-Operation Inspection and Service Loader Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/ServiceMount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Filling the Bucket Operating the LoaderOperation Lifting the Load Operation Dumping the Bucket Operating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Shutting Down the Implement Loader StorageTransporting the Tractor and Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideProblem Possible Cause Remedy Maintenance Section Maintenance 2412 01/11 Maintenance Section Lubrication Schedule Storage Daily MaintenanceStore loader with attachment securely attached Proper Torque for Fasteners Maintenance Maintenance Rhino To the OWNER/OPERATOR/DEALER SOM-01/11 F-3660C Printed U.S.A