Servis-Rhino 4211B manual Dismounting Loader, Mounting Loader

Page 40

ASSEMBLY

ASSEMBLY

Dismounting Loader

1.Locate tractor and loader on firm level ground.

2.Rotate parking stands from storage position to operation position by removing linch pins and clevis pin. Inner tube of parking stand is now free to slide within outer tube. Reinstall clevis pin and linch pin when parking stands are in operation position. See Figure Asm-L- 0089.

3.Level and lower bucket to ground. Rotate bucket down slightly to remove pressure on hitch pins (See Figure Asm-L-0090).

4.Remove lynch pins and hitch pins from mounting.

5.Start tractor engine and release brakes. Retract lift cylinders, allowing parking stands to support weight of loader. Drive tractor forward slightly so parking stands are firmly positioned. Operate loader control lever to extend lift cylinders, allowing top of loader upright to rotate forward out of upper mounting saddle. Operate loader control lever to retract bucket cylinder, which will curl bucket backward causing the loader upright to lift off of the mounting shaft. Continue to curl bucket until loader upright has rotated upward from the mounting position to clear front tires or fenders on tractor.

6.Stop engine and apply brakes. Disconnect hydraulic hoses from tractor.

7.Start tractor engine and release brakes. Slowly back tractor out of loader.

Mounting Loader

Mounting is basically reverse of dismounting.

1.Slowly drive tractor up to loader. Shut off tractor and apply brakes.

2.Connect hydraulic hoses.

3.Start engine and release brakes. Operate loader control lever to extend bucket cylinder, which will rotate bucket down, causing the loader upright to rotate downward placing mounting shaft in mounting pocket. Operate loader control lever to retract lift cylinders, causing the top of loader upright to rotate rearward. Continue to rotate loader upright into mounting saddle until upright will no longer rotate.

4.Shut off tractor, apply brakes.

5.Install hitch pins and linch pins, into mounting.

6.Remove linch pins and clevis pins from parking stands, rotate stands into storage position and secure with clevis pins and linch pins (Figure Asm-L-0089).

4211B 02/10

Assembly Section 3-6

© 2010 Alamo Group Inc.

Image 40

Contents 4211B To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices4211B 02/10 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 4211B 02/10 Safety Section Safety SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety See Your Rhino Dealer Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 4211B 02/10 Safety Section Loader Safety Safety Federal Laws and Regulations This Act SeeksPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly InstructionsAssembly Proper Rear Ballasting and Wheel Spacing Dismounting Loader and Mounting Loader to Tractor Dismounting Loader Mounting LoaderAttaching Pin on Bucket Mounting and Dismounting Attachment Mounting Attachment to LoaderWhen Connecting an Attachment to the Loader Quick Hitch Assembling Quick Attach Device Installing Quick Attach Device Page Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Rops and Seat Belt Tractor RequirementsTractor Lighting and SMV Emblem Getting On and Off the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/ServiceLoader Pre-Operation Inspection and Service Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Operating the Loader Filling the BucketOperation Lifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Transporting the Tractor and Implement Loader StorageShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Page Maintenance Section Maintenance 4211B 02/10 Maintenance Section Lubrication Schedule Daily Maintenance Cylinder Service Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly StorageStore loader with attachment securely attached Proper Torque for Fasteners Maintenance Maintenance Rhino To the OWNER/OPERATOR/DEALER 4211B Loader