Northern Industrial Tools 10000 BDG owner manual PRE-START UP Preparations, Extension Cords, Vcr

Page 8

The figures given above are for an average load such as a blower or fan. If the electric motor is connected to a hard starting load such as an air compressor, it will require more starting current. If it is connected to a light load or no load such as a power saw, it will require less starting current. The exact requirement will also vary with the brand or design of the motor.

Generators respond to severe overloading differently than the power line. When overloaded, the engine is not able to supply enough power to bring the electric motor up to operating speed. The generator responds to the high initial starting current, but the engine speed drops sharply. The overload may stall the engine. If allowed to operate at very low speeds, the electric motor starting winding will burn out in a short time. The generator head winding might also be damaged.

Running the generator under these conditions may result in damage to the generator stator as well as the electric motor windings. Because the heavy surge of current is required for only an instant, the generator will not be damaged if it can bring the motor up to speed in a few seconds. If difficulties in starting a motor are experienced, turn off all other electrical loads and if possible reduce the load on the electric motor.

EXTENSION CORDS

When electric power is to be provided to various loads at some distance from the generator, extension cords can be used. These cords should be sized to allow for distance in length and amperage so that the voltage drop between the set and point of use is held to a minimum.

 

Current/Pow er

Maximum Extension Cord Length

 

 

 

 

Amps

 

Load

#10

 

#12

 

#14

 

#16

 

 

 

 

at

 

(watts)

Ga.

 

Ga.

 

Ga.

 

Ga.

 

 

 

 

240V

 

 

Cord

 

Cord

 

Cord

 

Cord

 

 

 

 

10

 

2400

250’

 

150’

 

100’

 

75’

 

 

 

 

20

 

4800

125’

 

75’

 

50’

 

25’

 

 

 

 

30

 

7200

60’

 

35’

 

25’

 

10’

 

 

 

 

40

 

9600

30’

 

15’

 

10’

 

*

 

 

 

 

50

 

12000

15’

 

*

 

*

 

*

 

 

 

 

CAUTION: Equipment damage can result from the

 

 

 

 

low voltage caused by using an extension cord with a

 

 

 

 

small wire size.

 

 

 

 

 

 

 

 

 

 

 

Use this chart to estimate the total load on

your

 

 

 

 

generator.

 

 

 

 

 

 

 

 

 

 

 

For Determining Generator Load Requirements

 

 

 

 

Device

 

 

 

 

 

Running Watts

 

 

 

 

Air Conditioner (12,000 Btu)

 

 

1700 (a)

 

 

 

 

Battery Charger (20 Amp)

 

500

 

 

 

 

 

Belt Sander (3”)

 

 

 

1000

 

 

 

 

 

Chain Saw

 

 

 

1200

 

 

 

 

 

Circular Saw (6-1/2”)

 

900

 

 

 

 

 

Coffee Maker

 

 

 

1000

 

 

 

 

 

Compressor (1 HP)

 

 

2000 (a)

 

 

 

 

Compressor (3/4 HP)

 

 

1800 (a)

 

 

 

 

 

 

 

 

 

 

*Not recommended

7

 

 

 

 

 

 

Compressor (1/2 HP)

 

1400 (a)

 

 

Curling Iron

 

700

 

 

 

 

 

 

 

Dishwasher

 

1200

 

 

Edge Trimmer

 

500

 

 

Electric Nail Gun

 

1200

 

 

Electric Range (one element)

 

1500

 

 

Electric Skillet

 

1250

 

 

Freezer

 

800 (b)

 

 

 

 

 

 

 

Furnace Fan (1/3 HP)

 

1200 (a)

 

 

Hair Dryer

 

1200

 

 

Hand Drill (1”)

 

1100

 

 

Hand Drill (1/2”)

 

875

 

 

Hand Drill (3/8”)

 

500

 

 

Hand Drill (1/4”)

 

250

 

 

 

 

 

 

 

Hedge Trimmer

 

450

 

 

Home Computer

 

150

 

 

Impact Wrench

 

500

 

 

Jet Pump

 

800 (a)

 

 

Lawn Mower

 

1200

 

 

Light Bulb

 

100

 

 

 

 

 

 

 

Microwave Oven

 

700

 

 

Milk Cooler

 

1100 (a)

 

 

Oil Burner on Furnace

 

300

 

 

Oil Fired Space Htr (140,000 Btu)

 

400

 

 

Oil Fired Space Htr (85,000 Btu)

 

225

 

 

Oil Fired Space Htr (30,000 Btu)

 

150

 

 

 

 

 

 

 

Oven

 

4500

 

 

Paint Sprayer, Airless (1/3 HP)

 

600 (a)

 

 

Paint Sprayer, Airless (handheld)

 

150

 

 

Radio

 

200

 

 

Refrigerator

 

600 (b)

 

 

Slow Cooker

 

200

 

 

 

 

 

 

 

Submersible Pump (1-1/2 HP)

 

2800 (a)

 

 

Submersible Pump (1 HP)

 

2000 (a)

 

 

Submersible Pump (1/2 HP)

 

1500 (a)

 

 

Sump Pump

 

600 (a)

 

 

Table Saw (10”)

 

2000 (a)

 

 

Television

 

500

 

 

 

 

 

 

 

Toaster

 

1000

 

 

Vacuum cleaner

 

250

 

 

VCR

 

70

 

 

Water Heater

 

3000

 

 

Weed Trimmer

 

500

 

(a)Hard-starting motors require 3 to 5 times the rated running watts.

(b)These loads may require up to 15 minutes to restart due to its normal build up of compressor head pressure.

NOTE: For extremely hard to start loads such as air conditioners and air compressors, consult the equipment dealer to determine the maximum wattage.

PRE-START UP PREPARATIONS

Your generator has been thoroughly tested prior to shipment from the factory. However, damage can occur during shipping, so be sure to check for damaged parts, loose or missing nuts and bolts. If the aforementioned problems occur, call customer service at 1-800-270-0810.

Image 8
Contents 10000 BDG Table of Contents Thank YOUSpecifications Machine Component Identification DescriptionGenerator Features Ansi Safety Definitions Rules for Safe OperationsIntroduction References 1-3 Circuit BreakersInstallation To determine belt tensionExample = 600W When connecting Resistive load such as Load ApplicationStarting Electric Motors 120V, 60 Hz MotorsPRE-START UP Preparations Extension CordsCurrent/Pow er Maximum Extension Cord Length VCRGenerator Care Operating SpeedLoad Output RPMTroubleshooting Problem Possible Causes Possible Remedies

10000 BDG specifications

Northern Industrial Tools 10000 BDG is a versatile and powerful tool designed for both professional and amateur users. This heavy-duty tool is noted for its exceptional performance and reliability, making it a prime choice among those who require quality in their equipment.

One of the most notable features of the Northern Industrial Tools 10000 BDG is its robust construction. Built with high-quality materials, this tool is designed to withstand rigorous use and harsh conditions. Its durable exterior is resistant to wear and tear, ensuring longevity and consistent performance over time.

The 10000 BDG model boasts an impressive motor that delivers substantial power, enabling it to tackle a myriad of tasks with ease. Whether you're working on a construction site, doing automotive repairs, or managing a DIY project at home, this tool provides the versatility needed to complete tasks efficiently. The powerful motor is further complemented by an ergonomic design that allows for easy handling and operation, reducing user fatigue during extended use.

Another significant feature of this tool is its array of advanced technologies. Northern Industrial Tools has incorporated cutting-edge innovations that enhance the functionality of the 10000 BDG. The inclusion of a variable speed control allows users to adjust the speed according to their needs, making it suitable for a wide variety of applications. The tool also comes equipped with a built-in safety system, which includes an automatic shut-off feature that activates in case of overheating, ensuring user safety and preventing damage to the tool.

In terms of characteristics, the Northern Industrial Tools 10000 BDG is notably lightweight, making it easy to transport and maneuver. This feature is particularly beneficial for professionals who frequently move between job sites. The compact design allows it to be stored easily when not in use, saving valuable space in workshops or garages.

Furthermore, the 10000 BDG is designed for easy maintenance. Routine upkeep can be performed without requiring specialized tools, ensuring that users can keep their equipment in optimal condition with minimal effort.

In summary, the Northern Industrial Tools 10000 BDG stands out as a durable, powerful, and user-friendly tool that meets the demands of various tasks. Its advanced features and technologies make it a reliable choice for anyone needing an efficient and robust tool capable of delivering exceptional performance in diverse conditions.