MTD Series 580 warranty Setup Adjustment, Slip starter rope into rope guide Tighten wing nut

Page 6

3

Setup and

Adjustment

NOTE: This Operator’s Manual covers several models. Lawn Mower features vary by model. Not all features discussed (or engines pictured) in this manual are applicable to all Lawn Mower models.

NOTE: Stand behind the mower as if you were going to operate it. Your right hand cor- responds to the right side of the mower; your left hand corresponds to the left side of the mower.

NOTE: Each end of the lower handle must be placed in the same relative position.

IMPORTANT This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructed in the accompanying engine manual BEFORE operating your mower.

A

B

Figure 3-1: Unfold handle and tighten hardware.

Hardware Pack

Wing Nuts (2) Carriage Bolts (2)

B

A

Figure 3-2: Secure lower handle to mounting brackets.

A

B

D

C

Figure 3-3: Pull recoil starter through rope guide and tighten.

1.Remove any packing material which may be between upper and lower handles.

a.Pull up and back on upper handle as shown in Figure 3-1. Make certain the lower handle is seated securely into the handle mounting brackets.

b.Tighten hand knobs securing upper handle to lower handle. Make sure that each carriage bolt is seated properly in the handle.

2.Locate hairpin clip in one hole on the weld pin on each side of lower handle.

NOTE: Your mower is shipped with the handle in the higher height position.

a.Remove hairpin clip from this hole. Using a pair of pliers, insert hairpin clip into the other hole on the weld pin. Repeat on other side. See Figure 3-2.

b.Insert a carriage bolt from the hardware pack into the upper hole on the handle mounting bracket. Secure with one plastic wing nut, also included in the hardware pack. Repeat on other side with remaining items from hardware pack.

3.The rope guide is attached to the right side of the upper handle. Loosen the wing nut which secures the rope guide.

a.Hold blade control handle against upper handle.

b.Pull starter rope out of the engine. Release blade control handle. See Figure 3-3.

c.Slip starter rope into rope guide.

d.Tighten wing nut.

4.Insert post on cable ties into holes provided on the lower handle. Pull cable tie tight and trim excess.

5.If not already installed, assemble rear wheels as described below:

a.Place rear of the mower deck on raised blocks.

b.Remove lock nut from pivot arm assembly (on select models, these may be included separately in a plastic bag).

Figure 3-4: Secure cable to handle using cable ties.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Rotary Mower Model Series 21/2006Table of Contents Finding and Recording Model NumberCustomer Support Slope Gauge Safe Operation Practices Your ResponsibilitySlope Operation Setup Adjustment Slip starter rope into rope guide Tighten wing nut5If not already installed, assemble rear wheels Firmly against top Grass catcherOperating Your Lawn Mower Know Your Lawn MowerUsing Grass Catcher Using Your Lawn MowerUsing as Mulcher Starting EngineMaintaining Your Lawn Mower Off-Season Storage Blade CareReplacing Rear Flap Sonal injuryFor repairs beyond Trouble ShootingProblem Cause Remedy Listed here, contactSafety Labels Safety Label Found On Your Lawn MowerModel Series Pin Bar Tread Zag TreadParts List To order replacement Parts, call Or visit us on Web atMANUFACTURER’S Limited Warranty for

Series 580 specifications

The MTD Series 580 is a versatile and powerful machine that has garnered attention in the realm of outdoor equipment, known for its innovative features and robust performance. Designed primarily for homeowners and professional landscapers alike, this model stands out due to its combination of efficiency, durability, and user-friendly interface.

One of the main features of the MTD Series 580 is its powerful engine, which typically ranges in displacement and power output, catering to various yard sizes and terrains. This powerful engine ensures that the machine can tackle tough tasks, including mowing extensive lawns, managing overgrown grass, and executing clean cuts in challenging environments.

The MTD Series 580 incorporates advanced cutting technology, which includes a high-performance, mulching blade designed to deliver precision cuts while reducing grass clippings. This feature promotes a healthier lawn by allowing the mulched grass clippings to decompose naturally, returning essential nutrients back to the soil. Additionally, the adjustable cutting height feature allows users to customize their mowing preferences, ensuring that they can achieve the exact grass length desired.

Ergonomics and comfort are central to the design of the MTD Series 580. With an adjustable seat and an intuitive control panel, operators can easily maneuver the machine for prolonged periods without discomfort. The easy-to-reach controls simplify operation, making it suitable for both professionals and DIY enthusiasts.

Moreover, the MTD Series 580 comes equipped with advanced safety features, including automatic blade brakes and enhanced stability controls. This ensures that users can operate the machine safely, even on uneven terrain. The robust construction of the chassis not only provides stability but also enhances the overall longevity of the machine, with high-quality materials designed to withstand harsh outdoor conditions.

Another notable characteristic of the MTD Series 580 is its fuel efficiency, made possible by the innovative engine technology that minimizes emissions and maximizes power output. This makes the machine environmentally friendly while saving on operational costs, a growing concern among today’s eco-conscious consumers.

In summary, the MTD Series 580 is more than just an outdoor machine; it represents a blend of power, safety, and comfort, tailored to meet the demands of both homeowners and professionals. With its advanced features and technologies, it stands out as a reliable investment for tackling various outdoor challenges effectively and efficiently.
Top Page Image Contents