MTD 500, 510 manual Storing Your LOG Splitter, Troubleshooting, Problem Cause Remedy

Page 12

SECTION 7: STORING YOUR LOG SPLITTER

Prepare your log splitter for storage at the end of the season or if the log splitter will not be used for 30 days or more.

WARNING: Never store machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark, or where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc.

•Clean the log splitter thoroughly.

NOTE: We do not recommend the use of pressure washers or garden hose to clean your unit. They may cause damage to the log splitter components, or the engine. The use of water will result in shortened life and reduce serviceability.

•Wipe unit with an oiled rag to prevent rust, especially on the wedge and the beam.

•Drain fuel tank. Always drain fuel into approved container outdoors, away from open flame. Be sure that engine is cool before draining the fuel. Do not smoke while handling fuel.

•Start the engine and let it run until the fuel lines and carburetor are empty.

•Remove spark plug. Holding a rag over the cylinder hole, pour approximately 1/2 ounce (approximately one tablespoon) of engine oil into cylinder and crank slowly to distribute the oil.

•Replace spark plug.

•Do not store gasoline from one season to another.

•Replace your gasoline can if it starts to rust. Rust and/or dirt in the gasoline will cause problems.

•Store unit in a clean, dry area. Do not store next to corrosive materials, such as fertilizer.

NOTE: If storing in an unventilated or metal storage shed, be certain to rustproof the equipment by coating with a light oil or silicone.

SECTION 8: TROUBLESHOOTING

Problem

 

Cause

 

Remedy

 

 

 

 

 

Engine fails to start

1.

Spark plug wire disconnected.

1.

Connect wire to spark plug.

 

2.

Fuel tank empty or stale fuel.

2.

Fill tank with clean, fresh gasoline.

 

3.

Throttle control lever not in correct

3.

Move throttle lever to FAST position.

 

 

starting position.

 

 

 

4.

Choke, if equipped, not in CHOKE

4.

Move choke to CHOKE position.

 

 

position.

 

 

 

5.

Engine (if equipped with primer) not

5.

Prime engine.

 

 

primed properly.

 

 

 

6.

Blocked fuel line.

6.

Clean fuel line.

 

7.

Faulty spark plug.

7.

Clean, adjust gap, or replace.

Engine runs erratic

1.

Spark plug wire loose.

1.

Connect and tighten spark plug wire.

 

2.

Unit running on CHOKE, if so

2.

Move choke lever to OFF position.

 

 

equipped.

 

 

 

3.

Blocked fuel line or stale fuel.

3.

Clean fuel line; fill tank with clean, fresh

 

 

 

 

gasoline.

 

4.

Water or dirt in fuel system.

4.

Drain fuel tank. Refill with fresh fuel.

 

5.

Dirty air cleaner.

5.

Clean or replace air cleaner.

 

6.

Carburetor out of adjustment.

6.

See authorized service dealer.

Engine overheats

1.

Engine oil level low.

1.

Fill crankcase with proper oil.

 

2.

Dirty air cleaner.

2.

Clean or replace air cleaner.

 

3.

Carburetor not adjusted properly.

3.

See authorized service dealer.

NOTE: For repairs beyond those listed above, contact your nearest authorized service center.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General PracticesPreparation Maintenance and Storage OperationYour Responsibility Assembling Your LOG Splitter Preparing the Log Splitter Know Your LOG Splitter Stopping EngineControl Handle Beam LocksUsing the Log Splitter Operating Your LOG SplitterGas and Oil Fill-Up Starting EngineRaising and Lowering Beam Transporting the Log SplitterOperating Tips Adjusting Your LOG Splitter Wedge AssemblyMaintaining Your LOG Splitter Hydraulic FluidBeam and Splitting Wedge Hose ClampsEngine Flexible Pump CouplerTroubleshooting Problem Cause RemedyStoring Your LOG Splitter Hydraulic Cylinder Troubleshooting Parts List for Model Series 500 Model Series 500 Part DescriptionMANUFACTURER’S Limited Warranty for

500, 510 specifications

The MTD 500 and MTD 510 are innovative machines designed for efficiency and versatility in various agricultural applications. These models are engineered to meet the rigorous demands of modern farming, offering exceptional performance and reliability.

The MTD 500 is distinguished by its robust construction and advanced features that enhance productivity. One of its most notable characteristics is the powerful engine, which provides high torque and enables the machine to handle heavy loads with ease. This model is equipped with a user-friendly control panel that allows operators to quickly adjust settings based on their specific needs, ensuring optimal performance in different terrains and conditions.

The MTD 510 takes the concept of efficiency a step further, incorporating advanced technologies that streamline operations. A key feature of the MTD 510 is its precision farming capabilities, which utilize GPS technology for accurate field navigation. This allows farmers to maximize their yields and minimize waste by ensuring that inputs are applied precisely where needed. The machine's onboard sensors and data analytics provide real-time feedback, helping operators make informed decisions that enhance productivity.

Both the MTD 500 and MTD 510 are designed for versatility, allowing them to be used for a variety of tasks, including tilling, plowing, and harvesting. Their adaptable attachments make it easy to switch between tasks, reducing downtime and improving overall efficiency. Additionally, these models are designed with comfort in mind, featuring ergonomic seating and advanced suspension systems that reduce operator fatigue during long working hours.

Safety is a paramount consideration in the design of the MTD 500 and 510. Both models are equipped with numerous safety features, including rollover protection systems and automatic shut-off mechanisms that protect operators in case of emergency. Furthermore, their durable build quality ensures longevity, minimizing maintenance costs and enhancing overall value for farmers.

In summary, the MTD 500 and MTD 510 represent cutting-edge solutions in agricultural technology. With their powerful engines, precision farming capabilities, versatility, and safety features, these machines are ideal for modern farmers looking to boost efficiency and productivity in their operations. As agriculture constantly evolves, the MTD 500 and 510 stand out as reliable tools that can adapt to the challenges of the industry.
Top Page Image Contents