MTD 500, 510 manual Important Safe Operation Practices, General Practices, Preparation

Page 3

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer, birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

General Practices

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 16 years to operate this machine. Children,16 years and over, should read and understand instructions and safety rules in this manual and should be trained and supervised by a parent.

4.Never allow adults to operate this machine without proper instruction.

5.Many accidents occur when more than one person operates the machine. If a helper is assisting in loading logs, never activate the control until the helper is a minimum of 10 feet from the machine.

6.Keep bystanders, helpers, pets, and children at least 20 feet from the machine while it is in operation.

7.Never allow anyone to ride on this machine.

8.Never transport cargo on this machine.

9.Hydraulic log splitters develop high fluid pressures during operation. Fluid escaping through a pin hole opening can penetrate your skin and cause blood poisoning, gangrene, or death. Give attention to the following instructions at all times:

a.Do not check for leaks with your hand.

b.Do not operate machine with frayed, kinked, cracked, or damaged hoses, fitting, or tubing.

c.Stop the engine and relieve hydraulic system pressure before changing or adjusting fittings, hoses, tubing, or other system components.

d.Do not adjust the pressure settings of the pump or

valve.

5.Leaks can be detected by passing cardboard or wood, while wearing protective gloves and safety glasses, over the suspected area. Look for discoloration of cardboard or wood.

6.If injured by escaping fluid, see a doctor immediately. Serious infection or reaction can develop if proper medical treatment is not administered immediately.

7.Keep the operator zone and adjacent area clear for safe, secure footing.

8.If your machine is equipped with an internal combustion engine and it is intended for use near any unimproved forest, brush, or grass covered land, the engine exhaust

should be equipped with a spark arrester. Make sure you comply with applicable local, state, and federal codes. Take appropriate fire fighting equipment with you.

9.This machine should be used for splitting wood only, do not use it for any other purpose.

10.Follow the instructions in the manual(s) provided with any attachment(s) for this machine.

Preparation

1.Always wear safety shoes or heavy boots.

2.Always wear safety glasses or safety goggles during operating this machine.

3.Never wear jewelry or loose clothing that might become entangled in moving or rotating parts of the machine.

4.Make sure machine is on level surface before operating.

5.Always block machine to prevent unintended movement, and lock in either horizontal or vertical position.

6.Always operate this machine from the operator zone(s) specified in the manual.

7.Logs should be cut with square ends prior to splitting.

8.Use log splitter in daylight or under good artificial light.

9.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add fuel while the engine is hot or running.

e.Allow engine to cool at least two minutes before refueling.

f.Never overfill the fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equipment. move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

j.Allow machine to cool 5 minutes before storing.

3

Image 3
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General PracticesPreparation Maintenance and Storage OperationYour Responsibility Assembling Your LOG Splitter Preparing the Log Splitter Beam Locks Know Your LOG SplitterStopping Engine Control HandleStarting Engine Using the Log SplitterOperating Your LOG Splitter Gas and Oil Fill-UpRaising and Lowering Beam Transporting the Log SplitterOperating Tips Hydraulic Fluid Adjusting Your LOG SplitterWedge Assembly Maintaining Your LOG SplitterFlexible Pump Coupler Beam and Splitting WedgeHose Clamps EngineTroubleshooting Problem Cause RemedyStoring Your LOG Splitter Hydraulic Cylinder Troubleshooting Parts List for Model Series 500 Part Description Model Series 500MANUFACTURER’S Limited Warranty for

500, 510 specifications

The MTD 500 and MTD 510 are innovative machines designed for efficiency and versatility in various agricultural applications. These models are engineered to meet the rigorous demands of modern farming, offering exceptional performance and reliability.

The MTD 500 is distinguished by its robust construction and advanced features that enhance productivity. One of its most notable characteristics is the powerful engine, which provides high torque and enables the machine to handle heavy loads with ease. This model is equipped with a user-friendly control panel that allows operators to quickly adjust settings based on their specific needs, ensuring optimal performance in different terrains and conditions.

The MTD 510 takes the concept of efficiency a step further, incorporating advanced technologies that streamline operations. A key feature of the MTD 510 is its precision farming capabilities, which utilize GPS technology for accurate field navigation. This allows farmers to maximize their yields and minimize waste by ensuring that inputs are applied precisely where needed. The machine's onboard sensors and data analytics provide real-time feedback, helping operators make informed decisions that enhance productivity.

Both the MTD 500 and MTD 510 are designed for versatility, allowing them to be used for a variety of tasks, including tilling, plowing, and harvesting. Their adaptable attachments make it easy to switch between tasks, reducing downtime and improving overall efficiency. Additionally, these models are designed with comfort in mind, featuring ergonomic seating and advanced suspension systems that reduce operator fatigue during long working hours.

Safety is a paramount consideration in the design of the MTD 500 and 510. Both models are equipped with numerous safety features, including rollover protection systems and automatic shut-off mechanisms that protect operators in case of emergency. Furthermore, their durable build quality ensures longevity, minimizing maintenance costs and enhancing overall value for farmers.

In summary, the MTD 500 and MTD 510 represent cutting-edge solutions in agricultural technology. With their powerful engines, precision farming capabilities, versatility, and safety features, these machines are ideal for modern farmers looking to boost efficiency and productivity in their operations. As agriculture constantly evolves, the MTD 500 and 510 stand out as reliable tools that can adapt to the challenges of the industry.