Multiquip CA4HC Always keep the work area well organized, Transporting, Maintenance Safety

Page 13

CA4HCTROWEL — RULES FOR SAFE OPERATION

NEVER Run engine without air filter. Severe engine damage may occur. Service air filter frequently to prevent carburetor malfunction.

NEVER place your feet or hands inside the guard rings while starting or operating this equipment.

AVOID wearing jewelry or loose fitting clothing that may snag on the controls or moving parts as this can cause a serious injury.

ALWAYS keep clear of rotating or moving parts while operating the trowel.

Moving Parts – Shut down the engine before performing service or maintenance functions. Contact with moving parts can cause serious injury.

ALWAYS check to make sure that the operating area is clear before starting the engine.

NEVER leave the machine unattended while running.

ALWAYS be sure the operator is familiar with proper safety precautions and operations techniques before using trowel.

ALWAYS keep the work area well organized.

ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the trowel is in operation.

WARNING

ALWAYS check to make sure that the operating area is clear before starting the engine.

No one other than the operator is to be in the working area when the trowel is in operation.

Always observe all applicable compulsory regulations relevant to environmental protection, especially, fuel storage, the handling of hazardous substances, and the wearing of protective clothing and equipment. Instruct the user as necessary, or, as the user, request this information and training.

ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.

Transporting

ALWAYS shutdown engine before transporting.

Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.

Drain fuel when transporting trowel over long distances or bad roads.

When placing the trowel inside a truck-bed for transport, always tie-down the trowel.

ALWAYS use proper lifting techniques when moving the trowel.

Maintenance Safety

NEVER lubricate components or attempt service on a running trowel.

ALWAYS allow the trowel a proper amount of time to cool before servicing.

Keep the trowel in proper running condition.

Fix damage to the trowel immediately and always replace broken parts.

Dispose of hazardous waste properly.Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.

DO NOT use food or plastic containers to dispose of hazardous waste.

Emergencies

ALWAYS know the location of the nearest fire extinguisher.

ALWAYS know the location of the nearest first aid kit.

In emergencies always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information is invaluable in the case of an emergency and could keep a serious situation from becoming a tragic one .

CA4HC WALK-BEHIND TROWEL — OPERATION MANUAL — REV. #0 (09/29/06) — PAGE 13

Image 13
Contents Model CA4HC Page Silicosis Warning CA4HCTROWEL-TABLE of Contents Height Engagement Lever CA4HC Trowel DimensionsCA4HC Trowel Specifications CA4HCTROWEL- SpecificationsPage Machine layout, location of components, checking of engine Training ChecklistDaily PRE-OPERATION Checklist CA4HCTROWEL- Daily PRE-OPERATION ChecklistIf you do not follow these directions CA4HCTROWEL- Safety Message Alert SymbolsAlways wear approved eye and hearing protection CA4HCTROWEL- Safety Message Alert SymbolsFatigue, illness or taking medicine SafetyAlways keep the work area well organized Maintenance SafetyTransporting EmergenciesOperation and Safety Decals CA4HCTROWEL- Operation and Safety DecalsCA4HCTROWEL- General Information Engine Honda GX120 4 H.P. gasoline engine CA4HCTROWEL- Controls and ComponentsInitial Servicing CA4HCTROWEL- Basic EngineHandleTube Installation All Models Assembly and InstallationThrottle Cable Throttle Lever Run Position Idle Position ShownYoke Eyelet Conical Nut Locking Nut CA4HCTROWEL- Handle AssembliesUnfolding the Trowel for Operation Quick Pitch Handle AssemblyDo not operate unless T-Handle Knob is securely in place Operational Position Upper Handle Handle KnobCA4HCTROWEL- PRE-INSPECTION Read safety instructions at the beginning of manualBefore Starting Engine Oil CheckExplosive Fuel CA4HCTROWEL- PRE-INSPECTIONLifting the Trowel Onto a Slab CA4HCTROWEL Initial START-UPStarting the Engine Starter Grip Stopping The EngineCA4HCTROWEL Operation Satisfactory manner Pitching The Blades Standard HandleCombo Blades Maintenance Schedule CA4HCTROWEL MaintenanceTrowel Arm Blade Surface CA4HCTROWEL MaintenanceTrowel Arm Removal Spider Plate Zerk Fitting Washer Zerk CapTrowel Blade Removal Re-AssemblyChanging Blades Only Blade Blade Arm Hex Head Bolt Lock WasherDecommissioning Trowel/Components Installing Pans Onto Finisher BladesCA4HCTROWEL Troubleshooting Trowel Troubleshooting Engine CA4HCTROWEL Troubleshooting EnginePage Page Payment Terms Mexico United Kingdom United StatesCanada Brazil Your Local Dealer is

CA4HC specifications

The Multiquip CA4HC is an advanced concrete mixer that combines efficiency and versatility, making it a preferred choice for both professionals and DIY enthusiasts. This robust machine is engineered to handle a variety of mixing tasks seamlessly, allowing users to tackle projects of varying sizes effectively.

One of the standout features of the CA4HC is its 4-cubic-foot capacity. This size strikes an ideal balance, enabling users to mix enough concrete for substantial jobs while retaining portability. The unit is equipped with a powerful Honda engine that ensures reliable performance, allowing users to achieve high-quality mixes consistently.

Technology-wise, the CA4HC incorporates a direct drive system that eliminates the need for belts and pulleys, thus reducing maintenance and enhancing durability. This design not only improves the mixer’s lifespan but also results in a quieter operation, creating a more pleasant working environment. The electric start feature adds convenience, enabling users to start the mixer effortlessly with minimal effort.

Another notable characteristic of the CA4HC is its heavy-duty construction. The mixer features a solid steel frame that provides stability and resistance to the rigors of everyday use. The drum itself is made from robust materials that resist wear and tear, ensuring longevity and reliability over time. Additionally, the drum’s design allows for easy pouring, reducing spills and improving efficiency during concrete pouring tasks.

Portability is a key attribute of the Multiquip CA4HC. The mixer comes with pneumatic tires that allow for easy transportation over different terrains. Its compact design makes it easy to store when not in use, saving valuable space in garages or job sites.

Safety has also been prioritized in the design of the CA4HC. The mixer is equipped with safety guards to protect users from moving parts, reducing the risk of accidents during operation. Its intuitive controls ensure that even those new to concrete mixing can operate it with confidence.

In summary, the Multiquip CA4HC is a powerful, versatile, and user-friendly concrete mixer designed to meet the needs of various projects. With its durable construction, efficient engineering, and integrated safety features, it stands out as a reliable tool for achieving consistent mixing results. Whether for construction professionals or home improvement enthusiasts, the CA4HC offers a combination of performance and practicality that is hard to beat.