Multiquip operation manual CA4HCTROWEL- General Information

Page 15

CA4HCTROWEL— GENERAL INFORMATION

Intended Use

Operate the CA4HCTrowel, tools and components in accordance with the manufacturer's instructions. Use of any other tools for stated operation is considered contrary to designated use. The risk of such use lies entirely with the user. The manufacturer cannot be held liable for damages as a result of misuse.

CA4HC Trowel Familiarization

This walk-behind trowel is designed for the floating and finishing of concrete slabs.

Take a walk around the trowel. Take notice of all the major components (see Figure 2) like the engine, blades, Standard or Quick Pitch™ handle, etc.

Read all the safety instructions carefully. Safety instructions will be found throughout this manual and on the trowel. Keep all safety information in good, readable condition. Operators should be well trained on the operation and maintenance of the trowel.

Before using your trowel, test it on a flat watered down section of finished concrete that is free of any debris and other objects.

This trial test run will increase your confidence in using the trowel and at the same time it will familiarize you with the trowel’s controls. In addition you will understand how the trowel handles under actual conditions.

Engine

This trowel is available with an 4 HP HONDA gasoline engine. Refer to the engine owner’s manual for instructions regarding the operation and maintenance of your engine. Please contact your nearest Multiquip Dealer for a replacement should the original manual disappear or otherwise become unusable.

Drive System

Power is transferred from the engine to the gearbox input shaft via a V-belt pulley drive system. The pulley engages using a centrifugal clutch. See Parts section of this manual.

Gearbox

The gearbox is located beneath the engine and transfers power to the spider assembly.The gearbox controls the rotational speed of the trowel and is equipped with two shafts (input and output).

Spider

The vertical output shaft of the gearbox connects to a machined hub called the spider. The spider has 4 arms that extend outward that are used for attachment of blades or other accessories. Remember as the gearbox output shaft rotates so does the spider assembly.

Guard Ring

This unit is equipped with a special rotating guard ring. It is designed to allow the operator to run the machine alongside walls, pipes, and obstructions without marring the surface.

Blades

The blades of the trowel finish the concrete as they are rotated around the surface. This trowel comes equipped with four combination (8 in./203mm wide) blades per rotor equally spaced in a radial pattern and attached to vertical rotating shaft by means of the spider assembly.

Centrifugal Clutch

In the event of a trowel runaway condition (operator releases the handle), a centrifugal clutch will stop the engine and bring the trowel to a halt.

CAUTION

NEVER attempt to lift the trowel by yourself. ALWAYS get the assistance of another person to help lift the trowel .

Training

For proper training, please use the “TRAINING CHECKLIST” located in the front of this manual (Page 8). This checklist will provide an outline for an experienced operator to provide training to a new operator

CA4HC WALK-BEHIND TROWEL — OPERATION MANUAL — REV. #0 (09/29/06) — PAGE 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model CA4HC Page Silicosis Warning CA4HCTROWEL-TABLE of Contents Height Engagement Lever CA4HC Trowel DimensionsCA4HC Trowel Specifications CA4HCTROWEL- SpecificationsPage Machine layout, location of components, checking of engine Training ChecklistDaily PRE-OPERATION Checklist CA4HCTROWEL- Daily PRE-OPERATION ChecklistIf you do not follow these directions CA4HCTROWEL- Safety Message Alert SymbolsAlways wear approved eye and hearing protection CA4HCTROWEL- Safety Message Alert SymbolsFatigue, illness or taking medicine SafetyEmergencies Maintenance SafetyAlways keep the work area well organized TransportingOperation and Safety Decals CA4HCTROWEL- Operation and Safety DecalsCA4HCTROWEL- General Information Engine Honda GX120 4 H.P. gasoline engine CA4HCTROWEL- Controls and ComponentsInitial Servicing CA4HCTROWEL- Basic EngineShown Assembly and InstallationHandleTube Installation All Models Throttle Cable Throttle Lever Run Position Idle PositionYoke Eyelet Conical Nut Locking Nut CA4HCTROWEL- Handle AssembliesOperational Position Upper Handle Handle Knob Quick Pitch Handle AssemblyUnfolding the Trowel for Operation Do not operate unless T-Handle Knob is securely in placeEngine Oil Check Read safety instructions at the beginning of manualCA4HCTROWEL- PRE-INSPECTION Before StartingExplosive Fuel CA4HCTROWEL- PRE-INSPECTIONCA4HCTROWEL Initial START-UP Lifting the Trowel Onto a SlabStarting the Engine Starter Grip Stopping The EngineCA4HCTROWEL Operation Pitching The Blades Standard Handle Satisfactory mannerCombo Blades Maintenance Schedule CA4HCTROWEL MaintenanceSpider Plate Zerk Fitting Washer Zerk Cap CA4HCTROWEL MaintenanceTrowel Arm Blade Surface Trowel Arm RemovalBlade Blade Arm Hex Head Bolt Lock Washer Re-AssemblyTrowel Blade Removal Changing Blades OnlyDecommissioning Trowel/Components Installing Pans Onto Finisher BladesCA4HCTROWEL Troubleshooting Trowel Troubleshooting Engine CA4HCTROWEL Troubleshooting EnginePage Page Payment Terms Your Local Dealer is United StatesMexico United Kingdom Canada Brazil

CA4HC specifications

The Multiquip CA4HC is an advanced concrete mixer that combines efficiency and versatility, making it a preferred choice for both professionals and DIY enthusiasts. This robust machine is engineered to handle a variety of mixing tasks seamlessly, allowing users to tackle projects of varying sizes effectively.

One of the standout features of the CA4HC is its 4-cubic-foot capacity. This size strikes an ideal balance, enabling users to mix enough concrete for substantial jobs while retaining portability. The unit is equipped with a powerful Honda engine that ensures reliable performance, allowing users to achieve high-quality mixes consistently.

Technology-wise, the CA4HC incorporates a direct drive system that eliminates the need for belts and pulleys, thus reducing maintenance and enhancing durability. This design not only improves the mixer’s lifespan but also results in a quieter operation, creating a more pleasant working environment. The electric start feature adds convenience, enabling users to start the mixer effortlessly with minimal effort.

Another notable characteristic of the CA4HC is its heavy-duty construction. The mixer features a solid steel frame that provides stability and resistance to the rigors of everyday use. The drum itself is made from robust materials that resist wear and tear, ensuring longevity and reliability over time. Additionally, the drum’s design allows for easy pouring, reducing spills and improving efficiency during concrete pouring tasks.

Portability is a key attribute of the Multiquip CA4HC. The mixer comes with pneumatic tires that allow for easy transportation over different terrains. Its compact design makes it easy to store when not in use, saving valuable space in garages or job sites.

Safety has also been prioritized in the design of the CA4HC. The mixer is equipped with safety guards to protect users from moving parts, reducing the risk of accidents during operation. Its intuitive controls ensure that even those new to concrete mixing can operate it with confidence.

In summary, the Multiquip CA4HC is a powerful, versatile, and user-friendly concrete mixer designed to meet the needs of various projects. With its durable construction, efficient engineering, and integrated safety features, it stands out as a reliable tool for achieving consistent mixing results. Whether for construction professionals or home improvement enthusiasts, the CA4HC offers a combination of performance and practicality that is hard to beat.
Top Page Image Contents