ENGLISH | NAMES AND FUNCTIONS OF PARTS | |||||||||||||
| ||||||||||||||
| FRONT PANEL |
|
|
|
| |||||||||
| q w e r |
| t |
| y | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
!4 | !3 | !2 | !1 | !0 |
q POWER SWITCH |
| r SOURCE DIRECT SWITCH |
| |
u
oi
yMUTING INDICATOR
oSPEAKERS 1 / 2 SWITCHES
These switches are used to select the speaker system(s) connected to the SPEAKER SYSTEM 1 / 2 terminals on the rear panel. If both the 1 and 2 switches are pressed to the low positions, two speaker systems can be used at the same time.
When headphones are used for listening, set both switches 1 and 2 to OFF (high positions).
!0BALANCE CONTROL
Turn the knob to correct an unbalanced program source such as stereo broadcast or to vary the output level of the left or right channel. Note that, if the BALANCE control is turned fully in one direction, the sound will not be heard from the speaker on the other side.
!1BASS AND TREBLE TONE
CONTROLS
Adjusts the tone by controlling the levels of two frequency bands. Turn each control toward (+) to enhance the corresponding frequency band, or toward
Pressing once switches the power ON, and pressing again switches it OFF.
• When the switch is not depressed, the audio |
signals are applied to the tone and balance |
Light up when the MUTING button in the remote controller is pressed.
TREBLE: Adjusts the high frequency level.
BASS: Adjusts the low frequency level.
If the POWER switch is in the ON position, the power of this unit can be turned ON/OFF by pressing the POWER button on the remote controller.
wSTANDBY INDICATOR
Lights up when the unit is in the standby mode.
control circuit, enabling the tone and balance |
to be adjusted using the knobs. |
• When the switch is depressed, the audio |
signals bypass the tone control circuit and |
the balance control circuit. Then, the tone |
control knob and the balance control knob |
do not function. |
NOTE:
Be sure to check the VOLUME control setting before pressing this switch to cancel muting. If the muting is canceled while the volume setting is high, the speakers could be damaged.
!2REC SELECTOR SWITCH
Selects the tape dubbing mode between tape decks or the signal output at the REC OUT jacks.
!3REMOTE SENSOR
eINPUT SELECTOR
Selects the program source to be recorded or played from the PHONO, CD, TUNER, AUX/
DVD, RECORDER 1
tFUNCTION INDICATORS
One of the indicators lights up to indicate the input source selected with the INPUT SELECTOR.
uVOLUME CONTROL
Adjusts the volume level.Turn the knob clockwise to increase the volume.
iLOUDNESS SWITCH
The LOUDNESS switch compensates for human hearing characteristics by boosting the bass and treble response at low volume levels to achieve a more pleasing tonal balance.
The remote sensor receives the infrared commands from the remote controller. When an infrared signal is received from the remote controller. The remote controller must always be pointed directry at the remote sensor.
!4PHONES JACK
Insert the standard phone plug of the headphones into this jack.
4