Land Pride PR2572, PR2596 manual Transporting, Operating Checklist, Operating Instructions

Page 15

Land Pride

Table of Contents

Section 2: Operating Procedures

Transporting

IMPORTANT: ALWAYS disengage PTO before raising the powered rake to transport position.

3.When raising the powered rake to the transport position, be sure that powershaft does not contact tractor or powered rake.

4.Be sure to reduce tractor ground speed when turning; and, leave enough clearance so the powered rake does not contact obstacles such as buildings, trees or fences.

5.Select a safe ground travel speed when transporting from one area to another. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely.

6.When traveling over rough or hilly terrain, shift tractor to a lower gear.

!CAUTION

When traveling on public roads whether at night or during the day, use accessory light and devices for adequate warning to operators of other vehicles. Comply with all federal, state and local laws.

Operating Checklist

1.Check chain tension. Refer to “Drive Chain Adjustment” on page 14.

2.Check oil level in gearbox and chaincase. Refer to “Lubrication” on page 20 of this manual.

3.Check that all plugs have been replaced properly in the gearbox and chaincase.

4.Be sure all bolts and nuts are tight.

5.Be certain all guards and shields are in place and secure.

6.Grease PTO shaft and all other grease fittings. Refer to “Lubrication” on page 20.

7.Check air pressure in gauge wheel tires. It should be 14 psi.

Operating Instructions

1.Operate with 540 rpm PTO tractor.

2.DO NOT engage PTO at full throttle.

3.Raking should not be done in wet conditions as soil will stick between the bars on the roller and reduce the digging ability of the powered rake.

4.DO NOT make sharp turns or attempt to back up while powered rake is in the ground.

5.DO NOT engage PTO with machine in the fully raised position.

6.DO NOT drop the 3 point hitch. Lower the rock rake slowly to the ground.

7.After raking the first 50 feet, stop and check to see that the powered rake is adjusted properly.

8.The powered rake must be level front to rear and side to side for proper performance. See “Setting Depth & Leveling” on page 13 to level the powered rake.

9.Operating depth will depend on conditions but normally will be just skimming the surface to 1" deep. See “Setting Depth & Leveling” on page 13 to set the operating depth. Operating too shallow will allow rocks and trash to pass under the roller while operating too deep will cause dirt to flow over the material control blade or too much dirt will be carried out the end into the windrow.

10.Ground speed should be between 3 and 5 mph for normal conditions. Under extremely rocky conditions or when moving a large windrow ground speed may have to be reduced for satisfactory performance. In general the slower the ground speed the better job the powered rake does of separating the dirt from the rocks. If the ground speed is too fast then dirt will pass over the top of the material control blade or too much dirt will be carried out the end into the windrow.

11.Proper operating depth and ground speed are interrelated and performance of the powered rake will improve with operator experience.

12.Normal operating angle of the roller is all the way (20 degrees) left or right but may be varied depending on what the conditions call for.

13.Periodically check for foreign objects wrapped around the roller or stuck in between the bars on the roller and remove them after disengaging PTO, turning off tractor, and removing ignition key

14.The danish tine package option loosens rocks and trash below the surface of the ground. Normal operating depth is 1" to 4" deep when needed.

6/06/06

PR2572 & PR2596 Powered Rakes 314-132M

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Powered Rakes Table of Contents Safety at All Times Keep Riders Off Machinery Use Safety Lights and DevicesPractice Safe Maintenance Transport Machinery SafelyAvoid High Pressure Fluids Hazard Tire SafetyPrepare for Emergencies Wear Protective Equipment818-230C 818-130C 818-229C818-255C 818-540C 818-254C838-094C 818-552COwner Assistance Using This ManualTractor Requirements Gauge Wheel and Frame AssemblyTines and Tine Frame Assembly Lift Arm Location and Hose Routing Tractor Hookup Shearing Hardware AssemblyAngling Assembly Tine Lift AssemblyDriveline Installation Operating Checklist TransportingOperating Instructions Leveling Left-To-Right Setting Depth and LevelingDrive Chain Adjustment Setting The DepthMaterial Control Blade Adjustment Optional Equipment Storage MaintenanceDrive Chain Maintenance Sprocket and Chain ReplacementFriction Clutch PTO Bottom and Top Seal InstallationPlate Slip Clutch Assembly Disassembly StepDriveline U-Joints Lubrication PointsRequired Double Joint ZerksDrive Chain Pivot BearingsGauge Wheel Spindle Gauge WheelTine Lift Arms PR2572 PR2596 PR2572 & PR2596 Powered RakeProblem Solution TroubleshootingIn-tpi Torque Values ChartTire Inflation Chart TireSize Inflation26 PR2572 & PR2596 Powered Rakes 314-132M Warranty Overall Unit and Driveline One year Parts and LaborDriveline Slip-Clutch Friction discs Considered wear items Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

PR2572, PR2596 specifications

Land Pride PR2596 and PR2572 are premier models in the Land Pride product line, known for their exceptional performance and durability in the field of agricultural and landscaping equipment. These finishing mowers are designed to meet the demands of professionals looking for high-quality results with ease of use and reliability.

One of the standout features of the PR2596 and PR2572 is their cutting width. The PR2596 boasts a generous 96-inch cutting width, while the PR2572 offers a more compact 72-inch option. This versatility allows operators to tackle various mowing tasks, from large commercial properties to smaller residential lawns, ensuring a clean and precise cut every time. The mowers are equipped with a floating deck that follows the contours of the ground, ensuring that uneven terrain is no obstacle for a flawless finish.

The construction of these mowers is robust, built with heavy-duty materials that withstand the rigors of daily use. The steel frame and deck provide strength and longevity, while the reinforced edges prevent damage from contact with obstacles like rocks and tree stumps. Additionally, the powder-coated finish enhances durability by resisting rust and corrosion, making these mowers perfect for long-term outdoor use.

Land Pride's PR2596 and PR2572 feature a rear discharge design, which ensures that clippings are evenly dispersed across the lawn. This prevents clumping and promotes healthier grass growth by returning nutrient-rich clippings to the soil. The adjustable cutting height, ranging from 1 to 4 inches, offers the flexibility needed for various grass types and desired lawn appearances.

Another key technology in these models is the innovative blade system. The mowers are fitted with high-quality blades designed for efficiency and longer-lasting sharpness. This not only ensures a clean cut but also reduces the frequency of blade maintenance and replacement, saving time and costs for operators.

For user comfort, the PR2596 and PR2572 are designed with easy-to-use controls and settings. The quick-attach mounting system simplifies connecting the mower to tractors, while the operator-friendly design enhances maneuverability and reduces operator fatigue during long mowing sessions.

In summary, the Land Pride PR2596 and PR2572 finishing mowers represent the pinnacle of performance and efficiency in landscape management. Their combination of durable construction, advanced mowing technologies, and user-centric design makes them an outstanding choice for those seeking reliable, high-quality equipment to meet their mowing needs.
Top Page Image Contents