Jonsered FC 2255W, BC 2255 manual Fitting other guards and cutting attachments

Page 15

ASSEMBLY

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D) and support ﬂange (F) on the output shaft.

G

F

D

B

C

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut.

Fitting other guards and cutting attachments

•Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

L

M C

A

•Fit the drive disc (B) on the output shaft.

H

P

B

C

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

•To dismantle, follow the instructions in the reverse order.

English – 15

Image 15

Contents Operator’s manual EPA Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what on the clearing saw? BC2255 What is WHAT?What is what on the clearing saw? FC2255, FC2255W Personal protective equipment General Safety PrecautionsMachine′s safety equipment Stop switchThrottle lockout Mufﬂer Cutting attachment guardVibration damping system Quick releaseLocking screw Locking nutCutting equipment Cutting equipmentSharpening grass cutters and grass blades Trimmer head Sharpening the saw bladeAssembling the cutting equipment AssemblyAssembling the handlebar and throttle Transport position, handlebarFitting the blade guard and saw blade FC2255, FC2255WBC2255 Fitting other guards and cutting attachments Triobalance harness Adjusting the harness and clearing sawSafety release Adjusting the harnessCorrect balance Fuel safety Fuel HandlingFuel Mixing FuelingCold engine Starting and StoppingCheck before starting Starting and stoppingHeated handles Warm engineStarting StoppingABC of clearing Basic safety rulesWorking Techniques General working instructionsWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeTrimming Grass trimming with a trimmer headCarburetor MaintenanceMufﬂer Fine adjustment of the idle speed TCorrectly adjusted carburetor Adjusting the start throttle speed BC2255Bevel gear Cleaning the air ﬁlterCooling system Air ﬁlterWinter use Temperature 0C 32F or colderTemperature -5C 23F or colder Spark plugMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataYour Warranty Rights and Obligations Federal Emission Control Warranty StatementTrimmy SII Page Auto Tap n’Go 45 Spin Tap n’Go 55 Spin ´z+RpG¶5¨ Page 1150803-95 ´z+RpG¶5¨ ´z+RpG¶5¨