Jonsered CS 2145, CS 2141, CS 2150 manual Basic cutting technique, General, Terms, Cutting

Page 20

SAFETY INSTRUCTIONS

2 Basic cutting technique

General

•Always use full throttle when cutting!

•Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load can lead to serious engine damage).

•Cutting from above = Cutting on the pull stroke.

•Cutting from below = Cutting on the push stroke.

See the section on ”How to avoid kickback” to find out why cutting on the push stroke increases the risk of kickback.

Terms:

Cutting

=

General term for cutting through wood.

Limbing

=

Cutting limbs off a felled tree.

Splitting

=

When the object you are cutting breaks off

 

 

before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the bar will not jam in the cut.

2Make sure the log will not split.

3Make sure the chain will not strike the ground or any other object during or

after cutting.

4Is there a risk of kick- back?

5Do the conditions and surrounding terrain affect your safety when working?

Two factors decide whether the chain will jam or the log will split. The first is how the log is supported and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom of the log. You need to support the log so that it will not trap the chain or split during cutting.

If the chain jams in the cut:

STOP THE ENGINE! Don’t try to pull the saw free. If you do you may damage the chain when the saw suddenly breaks free. Use a lever to open up the cut and free the bar.

The following instructions describe how to handle most types of situation that you will be faced with when using a chain saw.

Cutting

1The log is lying on the

ground. There is little risk of the chain jamming or the log splitting. However there is a risk that the chain will touch the ground when you finish the cut.

Cut all the way through the log from above. Try not to touch the ground as you finish the cut. Maintain full throttle but be prepared in case the chain snatches.

A If it is possible to turn the log you should stop cutting about 2/3 of the way through.

B Turn the log and finish the cut from the opposite side.

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents EPA KEY to Symbols SymbolsContents EPASafety Instructions Personal Protective EquipmentChain brake and front hand guard 3a StartingRight hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking brake band wear Checking the front hand guardChecking the inertia brake release Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesCutting equipment designed to minimise kickback BarSaw chain Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth Risk of kickback is increased with a badly sharpened chainTensioning the chain General advice on setting raker clearanceSetting the raker clearance Lubricating cutting equipment Chain oilFilling with chain oil Never use waste oilNeedle bearing maintenance Checking chain lubricationChecking wear on cutting equipment Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Never use the saw one- handed General rulesDo not let go of the handles Min m 10 ftBasic safety rules General Working InstructionsBasic cutting technique GeneralTerms CuttingTree felling technique Safe distanceLimbing Felling directionClearing the trunk and preparing your retreat FellingGeneral advice Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? What is what?Assembly Mounting guide bar and chainFuel Handling FuelmixGasoline Two-stroke oilFuelling Chain oilMin 3 m 10ftStart and Stop Start and stopStart StopMaintenance CarburetorStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Air filterMuffler Spark plugWinter use Adjustment of the oil pump Centrifugal cleaningCooling system Long-term storage Weekly maintenance Daily maintenanceMonthly maintenance Bar and chain combinations Technical DataRecommended original and replacement Emission Control Warranty Statement Your Warranty Rights Obligations108 88 2002W49

CS 2145, CS 2150, CS 2141 specifications

The Jonsered CS 2141, CS 2150, and CS 2145 chainsaws are renowned for their powerful performance and advanced technologies, making them the top choice for both professional loggers and enthusiastic DIYers. Each model shares a commitment to delivering reliability, efficiency, and precision in cutting, while still prioritizing user comfort and safety.

The CS 2141 model is designed with a robust 40.9 cc engine that provides strong power output while remaining lightweight, making it easy to maneuver. This chainsaw features a 15-inch guide bar, ideal for tackling small to medium-sized trees and clearing brush. The innovative fuel system ensures longer running times, reducing the frequency of refueling interruptions. A hallmark of this model is its Easy Start system, eliminating the hassle of hard starts to get you cutting quickly.

Moving up, the Jonsered CS 2150 boasts a slightly larger engine capacity of 50.2 cc, which translates to enhanced power, particularly useful for more demanding cutting tasks. This model is equipped with a 20-inch guide bar, allowing for efficient felling and limbing of larger trees. Its design incorporates the Air Injection air filtration system that separates debris from the air, extending the life of the air filter and reducing maintenance needs. The lightweight design coupled with anti-vibration technology makes operating this model comfortable, even during extended use.

The CS 2145 model is a versatile chainsaw that finds a perfect balance between power and weight. With a 45.7 cc engine, it provides excellent cutting performance for a range of applications. It features a 16-inch guide bar, making it adaptable for various tasks from pruning to more extensive logging work. Like its counterparts, the CS 2145 includes the Smart Start technology for effortless starting and an automatic oil pump to ensure a steady flow of lubrication to the chain, increasing the overall lifespan of the saw.

All three models utilize Jonsered's revolutionary X-Torq engine technology, which significantly reduces fuel consumption and emissions, underlining their commitment to environmentally friendly operation. Furthermore, each chainsaw is ergonomically designed, with focus on comfortable grip and controls that allow users to work with precision and ease.

In summary, the Jonsered CS 2141, CS 2150, and CS 2145 chainsaws combine cutting-edge technology with practical features that meet the needs of users in various cutting conditions. With powerful engines, advanced filtration systems, and user-friendly designs, these models set a high standard in the chainsaw market.
Top Page Image Contents