Jonsered CS 2141 Weekly maintenance Daily maintenance, Monthly maintenance, Long-term storage

Page 33

MAINTENANCE

Below you will find some general maintenance instructions. If you have more questions, contact your servicing dealer.

Weekly maintenance

Daily maintenance

1. Check that the AV

elements are not soft or

torn.

1

2

1. Check the throttle trigger

for smooth operation. If

any binding occurs, or if

engine fails to return to

idle, the saw should be

taken to your dealer,

before it is used again.

Also, be sure that the

trigger cannot be pulled

until the throttle trigger

lockout is depressed.

2. Clean the chain brake

and check its function

according to the

instructions. Make sure

that the chain catcher is

undamaged. Otherwise

replace it immediately.

3. Clean or replace the air

filter as necessary. Check

for damage or holes.

4. The bar should be turned

daily for more even wear.

Check the lubrication hole

in the bar, to be sure it is

not clogged. Clean the

bar groove, if the bar has

a sprocket tip, this should

be lubricated.

5. Check the function of the

1

2

3

4

5

2.

Lubricate the clutch drum

 

bearing.

3.

File off burrs, if any, on

 

the sides of the bar.

4.

Clean the spark plug and

 

check the gap.

 

The correct gap is 0,5 mm

 

(0,020 inch).

5.

Check the starter and the

 

recoil spring. Clean the

 

fins on the flywheel.

6.

Clean the cooling fins on

 

the cylinder.

7.

Clean or change the

 

screen in the muffler.

8.

Clean the carburetor body

 

and air box.

 

3

4

0,5 mm

 

 

5

6

 

 

7

 

8

oiler to be sure the bar

and chain receive proper

lubrication.

6

Monthly maintenance

6.

Sharpen the chain and

 

check its tension and

 

condition. Check the drive

 

sprocket for wear.

 

Replace if necessary.

7.

Check the starter and

 

starter cord for wear or

 

damage. Clean the air

 

intake slots on the starter

 

housing.

8.

Check for any loose nuts

 

and screws and retighten

 

if necessary.

9.

Test the stop switch to be

 

sure it shuts off the

 

engine.

7

8

9

1.Check the brake band on the chain brake for wear.

2.Check the clutch centre, clutch drum and clutch spring for wear.

3.Clean the outside of the carburetor.

4.Change the fuel filter.

5.Clean the inside of the fuel tank.

6.Clean the inside of the oil tank.

7.Check all cables and connections.

8.Change the spark plug.

9.Change the air filter.

1

2

3

4 5

6

7

8 0,5 mm

Long-term storage

Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard.

Clean the machine. See ”Weekly maintenance”.

9

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents EPA Symbols KEY to SymbolsEPA ContentsPersonal Protective Equipment Safety Instructions3a Starting Chain brake and front hand guardThrottle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the front hand guard Checking brake band wearChecking the inertia brake release Checking the brake triggerThrottle lock 5 basic rules Cutting EquipmentBar Cutting equipment designed to minimise kickbackSaw chain Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Risk of kickback is increased with a badly sharpened chainGeneral advice on setting raker clearance Setting the raker clearanceTensioning the chain Chain oil Lubricating cutting equipmentFilling with chain oil Never use waste oilChecking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackGeneral rules Do not let go of the handlesNever use the saw one- handed 10 ft Min mGeneral Working Instructions Basic safety rulesGeneral Basic cutting techniqueTerms CuttingSafe distance Tree felling techniqueLimbing Felling directionFelling Clearing the trunk and preparing your retreatFreeing a tree that has fallen badly = high accident risk General adviceCutting the trunk into logs Freeing a Trapped treeWhat is what? What is WHAT?Mounting guide bar and chain AssemblyFuelmix Fuel HandlingGasoline Two-stroke oilChain oil FuellingMin 3 m 10ftStart and stop Start and StopStart StopCarburetor MaintenanceStarter device Starter device assemblyChanging a broken or worn starter cord Tensioning the recoil springAir filter Needle bearing maintenanceMuffler Spark plugAdjustment of the oil pump Centrifugal cleaning Cooling systemWinter use Weekly maintenance Daily maintenance Monthly maintenanceLong-term storage Technical Data Recommended original and replacementBar and chain combinations Your Warranty Rights Obligations Emission Control Warranty Statement2002W49 108 88

CS 2145, CS 2150, CS 2141 specifications

The Jonsered CS 2141, CS 2150, and CS 2145 chainsaws are renowned for their powerful performance and advanced technologies, making them the top choice for both professional loggers and enthusiastic DIYers. Each model shares a commitment to delivering reliability, efficiency, and precision in cutting, while still prioritizing user comfort and safety.

The CS 2141 model is designed with a robust 40.9 cc engine that provides strong power output while remaining lightweight, making it easy to maneuver. This chainsaw features a 15-inch guide bar, ideal for tackling small to medium-sized trees and clearing brush. The innovative fuel system ensures longer running times, reducing the frequency of refueling interruptions. A hallmark of this model is its Easy Start system, eliminating the hassle of hard starts to get you cutting quickly.

Moving up, the Jonsered CS 2150 boasts a slightly larger engine capacity of 50.2 cc, which translates to enhanced power, particularly useful for more demanding cutting tasks. This model is equipped with a 20-inch guide bar, allowing for efficient felling and limbing of larger trees. Its design incorporates the Air Injection air filtration system that separates debris from the air, extending the life of the air filter and reducing maintenance needs. The lightweight design coupled with anti-vibration technology makes operating this model comfortable, even during extended use.

The CS 2145 model is a versatile chainsaw that finds a perfect balance between power and weight. With a 45.7 cc engine, it provides excellent cutting performance for a range of applications. It features a 16-inch guide bar, making it adaptable for various tasks from pruning to more extensive logging work. Like its counterparts, the CS 2145 includes the Smart Start technology for effortless starting and an automatic oil pump to ensure a steady flow of lubrication to the chain, increasing the overall lifespan of the saw.

All three models utilize Jonsered's revolutionary X-Torq engine technology, which significantly reduces fuel consumption and emissions, underlining their commitment to environmentally friendly operation. Furthermore, each chainsaw is ergonomically designed, with focus on comfortable grip and controls that allow users to work with precision and ease.

In summary, the Jonsered CS 2141, CS 2150, and CS 2145 chainsaws combine cutting-edge technology with practical features that meet the needs of users in various cutting conditions. With powerful engines, advanced filtration systems, and user-friendly designs, these models set a high standard in the chainsaw market.
Top Page Image Contents