Jonsered CS 2145, CS 2141 Emission Control Warranty Statement, Your Warranty Rights Obligations

Page 35

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

The EPA (The US Environmental Protection Agency) and Jonsered are pleased to explain the emissions control system warranty on your 2000 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards.

Jonsered must warrant the emission control system on your small nonroad engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. Your emission control system includes Parts such as the carburetor and the ignition system. Where a warrantable condition exists, Jonsered will repair your small nonroad engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

The 2000 and later small nonroad engines are warranted for two years. If any emission related part on your engine (as listed above) is defective, the part will be repaired or replaced by Jonsered.

OWNER’S WARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for the performance of the required maintenance listed in your Operator’s Manual. Jonsered recommends that you retain all receipts covering maintenance on your small nonroad engine, but Jonsered cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small nonroad engine owner, you should, however, be aware that Jonsered may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications or the use of parts not made or approved by the original equipment manufacturer.

You are responsible for presenting your small nonroad engine to a Jonsered authorized servicing dealer as soon as a problem exists.

The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered, at Sweden + 46 36 14 65 00.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine is delivered.

LENGTH OF COVERAGE

Jonsered warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Jonsered servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered at Sweden + 46 36 14 65 00.

WARRANTY PERIOD

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of ”repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS

The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Jonsered servicing dealer.

CONSEQUENTIAL DAMAGES

Jonsered may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modified parts can be grounds for disallowing a warranty claim. Jonsered is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest

authorized servicing dealer or call Jonsered at Sweden + 46 36 14 65 00.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all Jonsered authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Any Jonsered approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1.Carburetor and internal parts

2.Intake pipe, airfilter holder and carburetor bolts.

3.Airfilter and fuelfilter covered up to maintainance schedule.

4.Ignition System

a)Spark Plug, covered up to maintenance schedule

b)Ignition Module

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as defined in the operator’s manual.

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents EPA Symbols KEY to SymbolsEPA ContentsPersonal Protective Equipment Safety Instructions3a Starting Chain brake and front hand guardRight hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainRisk of kickback is increased with a badly sharpened chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Sharpening cutting teethTensioning the chain General advice on setting raker clearanceSetting the raker clearance Never use waste oil Lubricating cutting equipmentChain oil Filling with chain oilLubricating the bar tip sprocket Needle bearing maintenanceChecking chain lubrication Checking wear on cutting equipmentWhat is kickback? HOW to Avoid KickbackNever use the saw one- handed General rulesDo not let go of the handles 10 ft Min mGeneral Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatFreeing a Trapped tree General adviceFreeing a tree that has fallen badly = high accident risk Cutting the trunk into logsWhat is what? What is WHAT?Mounting guide bar and chain AssemblyTwo-stroke oil Fuel HandlingFuelmix Gasoline10ft FuellingChain oil Min 3 mStop Start and StopStart and stop StartCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordSpark plug Needle bearing maintenanceAir filter MufflerWinter use Adjustment of the oil pump Centrifugal cleaningCooling system Long-term storage Weekly maintenance Daily maintenanceMonthly maintenance Bar and chain combinations Technical DataRecommended original and replacement Your Warranty Rights Obligations Emission Control Warranty Statement2002W49 108 88

CS 2145, CS 2150, CS 2141 specifications

The Jonsered CS 2141, CS 2150, and CS 2145 chainsaws are renowned for their powerful performance and advanced technologies, making them the top choice for both professional loggers and enthusiastic DIYers. Each model shares a commitment to delivering reliability, efficiency, and precision in cutting, while still prioritizing user comfort and safety.

The CS 2141 model is designed with a robust 40.9 cc engine that provides strong power output while remaining lightweight, making it easy to maneuver. This chainsaw features a 15-inch guide bar, ideal for tackling small to medium-sized trees and clearing brush. The innovative fuel system ensures longer running times, reducing the frequency of refueling interruptions. A hallmark of this model is its Easy Start system, eliminating the hassle of hard starts to get you cutting quickly.

Moving up, the Jonsered CS 2150 boasts a slightly larger engine capacity of 50.2 cc, which translates to enhanced power, particularly useful for more demanding cutting tasks. This model is equipped with a 20-inch guide bar, allowing for efficient felling and limbing of larger trees. Its design incorporates the Air Injection air filtration system that separates debris from the air, extending the life of the air filter and reducing maintenance needs. The lightweight design coupled with anti-vibration technology makes operating this model comfortable, even during extended use.

The CS 2145 model is a versatile chainsaw that finds a perfect balance between power and weight. With a 45.7 cc engine, it provides excellent cutting performance for a range of applications. It features a 16-inch guide bar, making it adaptable for various tasks from pruning to more extensive logging work. Like its counterparts, the CS 2145 includes the Smart Start technology for effortless starting and an automatic oil pump to ensure a steady flow of lubrication to the chain, increasing the overall lifespan of the saw.

All three models utilize Jonsered's revolutionary X-Torq engine technology, which significantly reduces fuel consumption and emissions, underlining their commitment to environmentally friendly operation. Furthermore, each chainsaw is ergonomically designed, with focus on comfortable grip and controls that allow users to work with precision and ease.

In summary, the Jonsered CS 2141, CS 2150, and CS 2145 chainsaws combine cutting-edge technology with practical features that meet the needs of users in various cutting conditions. With powerful engines, advanced filtration systems, and user-friendly designs, these models set a high standard in the chainsaw market.
Top Page Image Contents