Jonsered CS 2141S, CS 2145S manual Muffler, Starter, Changing a broken or worn starter cord

Page 32

MAINTENANCE

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. This is best done with a wire brush. A blocked mesh will cause the engine to overheat and may lead to serious damage.

Note! The mesh must be replaced if it is damaged. If the mesh is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor mesh is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator.The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

A muffler equipped with a catalytic converter significantly reduces the amount of hydrocarbons (HC), nitrogen oxides (NO) and aldehydes in the exhaust fumes. Carbon monoxide (CO), which is poisonous and odorless, is not however reduced! Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

Starter

WARNING! When the recoil spring is wound

!up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Operator’s manual EPAKEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Stop switch Cutting equipmentVibration damping system MufflerGeneral rules Cutting equipment designed to reduce kickbackBar ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethSharpening cutting teeth Instructions considerably increases the risk of kickbackGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingIf the depth gauge setting is too large Tensioning the chainLubricating cutting equipment Chain oilFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chainChain oil Fuel HandlingFuel Fuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueGeneral Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling cut FellingDirectional cuts General advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HThrottle lockout Changing a broken or worn starter cord MufflerStarter Replacement of broken recoil and drive disc springs Air filterTensioning the recoil spring Fitting the starterAdjustment of the oil pump When making adjustmentsSpark plug Lubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderCooling system Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges050/1,3 mm 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage ´z+R4G¶5g¨ Page 1150203-95 ´z+R4G¶5g¨ ´z+R4G¶5g¨

CS 2145S, CS 2141S specifications

The Jonsered CS 2141S and CS 2145S chainsaws are powerful tools designed for both professional and avid hobbyist woodworkers. Known for their robust construction and efficient performance, these chainsaws embody reliability and advanced technology, making them ideal for a variety of cutting tasks.

One of the standout features of the Jonsered CS 2141S and CS 2145S is their powerful engines. The CS 2141S is equipped with a 40.9cc engine, while the CS 2145S boasts a slightly more powerful 45.7cc engine. This difference in engine size translates to enhanced cutting performance, allowing users to tackle larger logs and more demanding jobs with ease. Both models deliver excellent power-to-weight ratios, ensuring that users can work for extended periods without excessive fatigue.

These models also incorporate advanced technologies that elevate their functionality. One notable innovation is the X-Torq engine, which reduces fuel consumption and emissions. This is particularly beneficial for environmentally conscious users, as it helps lessen the ecological footprint without compromising on power or performance. Additionally, the effective anti-vibration system minimizes the impact of vibrations on the user, enhancing comfort and control during operation.

Another key characteristic of the CS 2141S and CS 2145S is their ease of use and maintenance. The Quick Release Air Filtration system allows for efficient cleaning and replacement, ensuring that the engine performs at its best. Furthermore, the chain brake feature provides added safety by automatically stopping the chain in the event of kickback, making these chainsaws safer to operate.

Both models are designed for versatility, featuring adjustable oil pumps that allow users to regulate the flow of bar and chain oil for improved lubrication and extended chain life. The ergonomically designed handles offer optimal grip and control, which is essential for precision cutting.

In summary, the Jonsered CS 2141S and CS 2145S chainsaws are powerful and efficient tools equipped with advanced technologies that promote ease of use, safety, and environmental sustainability. Whether for professional forestry work or home woodcutting projects, these models are reliable choices that deliver outstanding performance and durability.
Top Page Image Contents