Jonsered CS 2141S, CS 2145S manual High speed jet H, Correctly adjusted carburetor

Page 30

MAINTENANCE

High speed jet H

At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet.

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Checking, maintaining and servicing chain saw safety equipment

Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.6 mm (0,024 inch) thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

Checking the inertia brake release

With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle.

When the bar hits the stump the brake should be applied.

Checking the brake trigger

Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operator’s manual EPASymbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerBar General rulesCutting equipment designed to reduce kickback ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Instructions considerably increases the risk of kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainFuel Handling FuelChain oil Transport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HThrottle lockout Muffler StarterChanging a broken or worn starter cord Tensioning the recoil spring Replacement of broken recoil and drive disc springsAir filter Fitting the starterSpark plug Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocket Needle bearing lubricationCooling system Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+R4G¶5g¨ Page 1150203-95 ´z+R4G¶5g¨ ´z+R4G¶5g¨

CS 2145S, CS 2141S specifications

The Jonsered CS 2141S and CS 2145S chainsaws are powerful tools designed for both professional and avid hobbyist woodworkers. Known for their robust construction and efficient performance, these chainsaws embody reliability and advanced technology, making them ideal for a variety of cutting tasks.

One of the standout features of the Jonsered CS 2141S and CS 2145S is their powerful engines. The CS 2141S is equipped with a 40.9cc engine, while the CS 2145S boasts a slightly more powerful 45.7cc engine. This difference in engine size translates to enhanced cutting performance, allowing users to tackle larger logs and more demanding jobs with ease. Both models deliver excellent power-to-weight ratios, ensuring that users can work for extended periods without excessive fatigue.

These models also incorporate advanced technologies that elevate their functionality. One notable innovation is the X-Torq engine, which reduces fuel consumption and emissions. This is particularly beneficial for environmentally conscious users, as it helps lessen the ecological footprint without compromising on power or performance. Additionally, the effective anti-vibration system minimizes the impact of vibrations on the user, enhancing comfort and control during operation.

Another key characteristic of the CS 2141S and CS 2145S is their ease of use and maintenance. The Quick Release Air Filtration system allows for efficient cleaning and replacement, ensuring that the engine performs at its best. Furthermore, the chain brake feature provides added safety by automatically stopping the chain in the event of kickback, making these chainsaws safer to operate.

Both models are designed for versatility, featuring adjustable oil pumps that allow users to regulate the flow of bar and chain oil for improved lubrication and extended chain life. The ergonomically designed handles offer optimal grip and control, which is essential for precision cutting.

In summary, the Jonsered CS 2141S and CS 2145S chainsaws are powerful and efficient tools equipped with advanced technologies that promote ease of use, safety, and environmental sustainability. Whether for professional forestry work or home woodcutting projects, these models are reliable choices that deliver outstanding performance and durability.
Top Page Image Contents