Jonsered CS 2141S manual Spark plug, Lubricating the bar tip sprocket Needle bearing lubrication

Page 34

MAINTENANCE

Spark plug

The spark plug condition is influenced by:

Incorrect carburetor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

2 1

3

+

Recommended settings:

Bar 13"-15": Position 1

Bar 15"-18": Position 2

Bar 18"-20": Position 3

WARNING! The engine must be stopped

!when making adjustments.

34 – English

Image 34
Contents Operator’s manual EPASymbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Stop switchCutting equipment MufflerBar General rulesCutting equipment designed to reduce kickback ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Instructions considerably increases the risk of kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Assembly Fitting the bar and chainFuel Fuel HandlingChain oil Transport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules General Basic cutting techniqueTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor High speed jet HThrottle lockout Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Replacement of broken recoil and drive disc springsAir filter Fitting the starterSpark plug Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocket Needle bearing lubricationCooling system Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+R4G¶5g¨ Page 1150203-95 ´z+R4G¶5g¨ ´z+R4G¶5g¨

CS 2145S, CS 2141S specifications

The Jonsered CS 2141S and CS 2145S chainsaws are powerful tools designed for both professional and avid hobbyist woodworkers. Known for their robust construction and efficient performance, these chainsaws embody reliability and advanced technology, making them ideal for a variety of cutting tasks.

One of the standout features of the Jonsered CS 2141S and CS 2145S is their powerful engines. The CS 2141S is equipped with a 40.9cc engine, while the CS 2145S boasts a slightly more powerful 45.7cc engine. This difference in engine size translates to enhanced cutting performance, allowing users to tackle larger logs and more demanding jobs with ease. Both models deliver excellent power-to-weight ratios, ensuring that users can work for extended periods without excessive fatigue.

These models also incorporate advanced technologies that elevate their functionality. One notable innovation is the X-Torq engine, which reduces fuel consumption and emissions. This is particularly beneficial for environmentally conscious users, as it helps lessen the ecological footprint without compromising on power or performance. Additionally, the effective anti-vibration system minimizes the impact of vibrations on the user, enhancing comfort and control during operation.

Another key characteristic of the CS 2141S and CS 2145S is their ease of use and maintenance. The Quick Release Air Filtration system allows for efficient cleaning and replacement, ensuring that the engine performs at its best. Furthermore, the chain brake feature provides added safety by automatically stopping the chain in the event of kickback, making these chainsaws safer to operate.

Both models are designed for versatility, featuring adjustable oil pumps that allow users to regulate the flow of bar and chain oil for improved lubrication and extended chain life. The ergonomically designed handles offer optimal grip and control, which is essential for precision cutting.

In summary, the Jonsered CS 2141S and CS 2145S chainsaws are powerful and efficient tools equipped with advanced technologies that promote ease of use, safety, and environmental sustainability. Whether for professional forestry work or home woodcutting projects, these models are reliable choices that deliver outstanding performance and durability.